Request Quote
  1. Home
  2. Products
  3. Stainless Steel
  4. ASTM A312 TP317L Stainless Steel Pipes & Tubes

ASTM A312 TP317L Stainless Steel Pipes & Tubes

ASTM A312 TP317L stainless steel pipes and tubes (UNS S31703) with 3 to 4% Mo for higher pitting resistance, supplied and exported by Riyaarth Overseas.

ASTM A312 TP317L Stainless Steel Pipes & Tubes by Riyaarth Overseas

ASTM A312 TP317L (UNS S31703) is a low carbon, molybdenum bearing austenitic stainless steel with 18% to 20% chromium, 11% to 15% nickel and 3% to 4% molybdenum. The extra molybdenum compared with 316L gives better resistance to pitting and crevice corrosion in chloride solutions and to many acids, while the 0.035% carbon limit keeps it resistant to sensitisation when welded.

Buyers choose TP317L when 316L is not enough but a higher alloy is not justified, for example in flue gas desulphurisation, pulp bleaching and chemical process lines. Riyaarth Overseas supplies and exports TP317L seamless and welded pipes and tubes, with matching fittings and flanges on request.

Key Features

Higher molybdenum: Mo of 3.0% to 4.0% raises pitting and crevice corrosion resistance above 316L.

Low carbon: Carbon of 0.035% max reduces the risk of intergranular corrosion in the weld heat affected zone.

Acid resistance: Resists sulphuric, acetic, formic and phosphoric acid environments better than 316L in many conditions.

Same strength as 316: ASTM A312 sets the same 515 MPa tensile minimum as TP316, higher than TP316L.

Specifications

ParameterDetails
StandardsASTM A312 / ASME SA312 (pipe), ASTM A213 / SA213 and A249 / SA249 (tube), ASTM A269 (general service tube)
Grade / UNSTP317L (S31703)
Outside diameter rangePipe: 1/8 in to 24 in NPS; tube: from 6 mm OD upward
Wall thickness / scheduleSchedule 5S, 10S, 40S, 80S, 160; tube wall to order
LengthSingle random, double random and cut lengths
TypeSeamless and welded
EndsPlain end, bevelled end
Form / finishRound; annealed and pickled
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

TP317L is less common in stock than 316L, so larger or heavy wall sizes may be supplied from mill production. Give the full size list and any corrosion testing needs at the enquiry stage so that the right source can be chosen.

Chemical Composition

Limits per ASTM A312.

ElementComposition (%)
Carbon (C)0.035 max
Manganese (Mn)2.00 max
Phosphorus (P)0.045 max
Sulphur (S)0.030 max
Silicon (Si)1.00 max
Chromium (Cr)18.0 – 20.0
Nickel (Ni)11.0 – 15.0
Molybdenum (Mo)3.0 – 4.0

Mechanical Properties

Room temperature minimums per ASTM A312. Note that TP317L carries the same minimum strength as TP316, not the lower values of TP316L.

PropertyValue
Tensile strength, min515 MPa (75 ksi)
Yield strength (0.2%), min205 MPa (30 ksi)
Elongation in 50 mm, min35% longitudinal, 25% transverse
HardnessHBW 192 max / HRB 90 max (ASTM A213, A249, A269 tubes)
Densityapprox. 8.0 g/cm³

Equivalent Grades

SystemDesignation
UNSS31703
EN / Werkstoff1.4438 (X2CrNiMo18-15-4)
JISSUS317L
ASMESA312 TP317L

EN 1.4438 is the closest European grade. 317LMN (S31726) is a different, higher nitrogen and molybdenum grade and should not be treated as an equivalent.

Testing and Inspection

TP317L pipes and tubes are tested to ASTM A312 or the relevant tube standard.

  • Hydrostatic or eddy current test: On every length.
  • Positive material identification: Confirms molybdenum is in the 3% to 4% range and not mixed with 316L.
  • Intergranular corrosion test: ASTM A262 Practice E available on request.
  • Flattening and flaring tests: To confirm ductility.
  • Mechanical tests: Tensile and hardness per lot.
  • Third-party inspection: Witness inspection with EN 10204 3.2 certification.

Because 317L and 316L look the same, separate storage and PMI before dispatch are important to avoid mix-ups on site. Each length is marked with grade, size and heat number and matched to its certificate.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources TP317L pipes and tubes from established mills and supplies them with EN 10204 3.1 certificates and heat numbers on every length. We can add matching 317L fittings and flanges to the same order, cut to length, and pack for export. Contact us with your sizes for a fast quote.

Applications

Flue gas desulphurisationAbsorber spray headers and slurry lines in coal fired power plants.
Pulp and paperBleach plant washers and lines handling chlorine dioxide bearing liquors.
Chemical processingLines carrying organic acids and dilute sulphuric acid.
PetrochemicalCondenser and process lines with chloride contamination.
Food processingLines for salty or acidic food products where 316L shows pitting.
Textile and dyeingPiping for hot, acidic dye liquors.

Frequently asked questions

What is the difference between 316L and 317L?

317L has more chromium (18% to 20%) and more molybdenum (3% to 4%) than 316L, which gives better resistance to pitting and crevice corrosion and to several acids.

Is 317L stronger than 316L?

Under ASTM A312, TP317L has a minimum tensile strength of 515 MPa and yield of 205 MPa, compared with 485 MPa and 170 MPa for TP316L.

Where is 317L commonly used?

Typical uses are flue gas desulphurisation systems, pulp bleach plants, chemical process lines and condensers where 316L has shown pitting.

Which filler metal is used for 317L?

ER317L filler metal is normally used. In severe service, a higher alloy filler may be specified so that the weld is not the weaker zone.