
ASTM A312 TP347 Stainless Steel Pipes & Tubes
ASTM A312 TP347 stainless steel pipes and tubes (UNS S34700), niobium stabilised for welded high temperature duty, supplied and exported by Riyaarth Overseas.

ASTM A312 TP347 (UNS S34700) is an 18/10 austenitic stainless steel stabilised with niobium (columbium). Niobium forms stable carbides, so chromium stays in solution and the steel resists intergranular corrosion after welding or after service in the 425 °C to 815 °C range. Its function is close to 321, but niobium is retained better through the welding arc.
TP347 and its high carbon version TP347H are used for hot process piping in refineries, boiler tubes and high temperature heat exchangers. Riyaarth Overseas supplies and exports TP347 and TP347H seamless and welded pipes and tubes with matching fittings when required.
Key Features
Niobium stabilised: Nb of at least ten times carbon, up to 1.00%, ties up carbon and prevents sensitisation.
Weld friendly: Niobium is not burned off in the arc like titanium, so 347 is often used as the filler and base metal for stabilised welds.
High temperature strength: Gives good creep and stress rupture properties, especially as TP347H.
Polishable: Without titanium carbonitrides, 347 takes a cleaner polished finish than 321.
Specifications
| Parameter | Details |
|---|---|
| Standards | ASTM A312 / ASME SA312 (pipe), ASTM A213 / SA213 and A249 / SA249 (tube), ASTM A376 (high temperature pipe) |
| Grades / UNS | TP347 (S34700), TP347H (S34709) |
| Outside diameter range | Pipe: 1/8 in to 24 in NPS; tube: from 6 mm OD upward |
| Wall thickness / schedule | Schedule 10S to 160 and XXS; tube wall to order |
| Length | Single random, double random and cut lengths |
| Type | Seamless and welded |
| Ends | Plain end, bevelled end |
| Form / finish | Round; annealed and pickled |
| Test certificate | EN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request |
For refinery service, purchasers often add a stabilising heat treatment, a carbon range or a niobium to carbon ratio in their own specification. These requirements should be shared with the enquiry so that the mill source can confirm them before order.
Chemical Composition
Limits per ASTM A312 for TP347.
| Element | Composition (%) |
|---|---|
| Carbon (C) | 0.08 max |
| Manganese (Mn) | 2.00 max |
| Phosphorus (P) | 0.045 max |
| Sulphur (S) | 0.030 max |
| Silicon (Si) | 1.00 max |
| Chromium (Cr) | 17.0 – 19.0 |
| Nickel (Ni) | 9.0 – 13.0 |
| Niobium (Nb / Cb) | 10 × C min, 1.00 max |
Mechanical Properties
Room temperature minimums per ASTM A312. TP347H has the same room temperature minimums, with higher allowable stresses at elevated temperature.
| Property | Value |
|---|---|
| Tensile strength, min | 515 MPa (75 ksi) |
| Yield strength (0.2%), min | 205 MPa (30 ksi) |
| Elongation in 50 mm, min | 35% longitudinal, 25% transverse |
| Hardness | HBW 192 max / HRB 90 max (ASTM A213, A249, A269 tubes) |
| Density | approx. 8.0 g/cm³ |
Equivalent Grades
| System | Designation |
|---|---|
| UNS | S34700 (347), S34709 (347H) |
| EN / Werkstoff | 1.4550 (X6CrNiNb18-10) |
| JIS | SUS347 |
| ASME | SA312 TP347 |
EN 1.4550 is the closest European grade to TP347. For TP347H in creep service, confirm the EN alternative with the design code.
Testing and Inspection
TP347 pipes and tubes are tested to ASTM A312 or the ordered tube standard.
- Hydrostatic or eddy current test: On every length.
- Intergranular corrosion test: ASTM A262 Practice E available on request.
- Positive material identification: Confirms niobium content and separates 347 from 304 and 321.
- Grain size check: For TP347H, as required by ASTM A213 and A312.
- Flattening and flaring tests: To confirm ductility.
- Third-party inspection: Witness inspection and EN 10204 3.2 certification.
Certificates show the niobium and carbon content, the heat treatment applied and the grain size result for 347H, and every length is marked for full traceability.
Why Choose Riyaarth Overseas
Riyaarth Overseas supplies TP347 and TP347H pipes and tubes from proven mills, with EN 10204 3.1 certificates and full heat traceability. We cut to length, pack for export and can add 347 fittings and flanges to the same shipment. Send your requirement for a prompt quote.
Applications






Frequently asked questions
What is the difference between 347 and 347H?
347H has carbon of 0.04% to 0.10% and a controlled grain size for higher strength in creep service. 347 allows up to 0.08% carbon with no lower limit.
Why choose 347 over 321?
Niobium survives the welding arc better than titanium, so 347 keeps its stabilisation in welds. Many refinery specifications prefer 347 for hot hydrogen and hydrocarbon service.
Is 347 resistant to polythionic acid stress corrosion cracking?
Stabilised grades such as 347, especially with a stabilising heat treatment, are widely used to reduce the risk of polythionic acid cracking during refinery shutdowns. The project specification should state the heat treatment.
What is the EN equivalent of TP347?
The closest European grade is 1.4550 (X6CrNiNb18-10).
