Request Quote
  1. Home
  2. Products
  3. Stainless Steel
  4. Stainless Steel Seamless Pipes & Tubes

Stainless Steel Seamless Pipes & Tubes

Stainless steel seamless pipes and tubes to ASTM A312, A213 and A269 in 304, 304L, 316 and 316L, supplied from stock and exported by Riyaarth Overseas.

Stainless Steel Seamless Pipes & Tubes by Riyaarth Overseas

Stainless steel seamless pipes and tubes are made from solid round billets that are pierced and then hot finished or cold drawn, so the wall has no weld seam. Pipe is ordered by nominal pipe size and schedule, mainly to ASTM A312 / ASME SA312, while tube is ordered by exact outside diameter and wall thickness to standards such as ASTM A213 for boiler and heat exchanger tubes and ASTM A269 for general service tubing.

Buyers choose seamless product when the line carries high pressure, cyclic loads or fluids where a uniform wall without a weld zone is preferred. Riyaarth Overseas supplies and exports seamless stainless steel pipes and tubes in the common austenitic grades 304, 304L, 316 and 316L, along with higher grades on request, cut to length and packed for sea freight.

Key Features

No weld seam: The wall is homogeneous around the full circumference, which removes the weld as a possible weak point under pressure, fatigue or corrosive attack.

Wide schedule range: Pipe is available from thin Schedule 5S and 10S up to Schedule 160 and XXS, so the same grade can be used for low pressure utility lines and high pressure process lines.

Solution annealed: Pipes and tubes are delivered heat treated and pickled, restoring full corrosion resistance and a clean surface after hot or cold working.

Dual certified grades: Material is commonly certified as 304/304L or 316/316L, meeting the strength of the standard grade and the low carbon limit of the L grade in one product.

Specifications

ParameterDetails
StandardsASTM A312 / ASME SA312 (pipe), ASTM A213 / ASME SA213 (boiler, superheater and heat exchanger tube), ASTM A269 (general service tube), ASTM A376 (high temperature service pipe)
Grades / UNSTP304 (S30400), TP304L (S30403), TP316 (S31600), TP316L (S31603), plus 304H, 316H, 317L, 321, 347, 309S and 310S on request
Outside diameter rangePipe: 1/8 in to 24 in NPS; tube: from 6 mm OD upward
Wall thickness / scheduleSchedule 5S, 10S, 40S, 80S, 160 and XXS for pipe; tube wall to order in mm or BWG
LengthSingle random, double random and cut lengths
TypeSeamless, hot finished or cold drawn
EndsPlain end, bevelled end, threaded end
Form / finishRound; annealed and pickled, bright annealed or polished
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

When ordering, state the standard, grade, NPS and schedule for pipe, or OD and minimum or average wall for tube, along with length and end finish. This avoids confusion between pipe and tube sizes, which differ for the same nominal figure.

Chemical Composition

Limits per ASTM A312 for the four most ordered grades.

ElementComposition (%)
Carbon (C)0.08 max (TP304, TP316), 0.035 max (TP304L, TP316L)
Manganese (Mn)2.00 max
Phosphorus (P)0.045 max
Sulphur (S)0.030 max
Silicon (Si)1.00 max
Chromium (Cr)18.0 – 20.0 (TP304, TP304L), 16.0 – 18.0 (TP316, TP316L)
Nickel (Ni)8.0 – 11.0 (TP304), 8.0 – 13.0 (TP304L), 11.0 – 14.0 (TP316), 10.0 – 14.0 (TP316L)
Molybdenum (Mo)2.00 – 3.00 (TP316, TP316L only)

Mechanical Properties

PropertyValue
Tensile strength, min515 MPa (75 ksi) for TP304 and TP316; 485 MPa (70 ksi) for TP304L and TP316L
Yield strength (0.2%), min205 MPa (30 ksi) for TP304 and TP316; 170 MPa (25 ksi) for TP304L and TP316L
Elongation in 50 mm, min35% longitudinal, 25% transverse (ASTM A312)
HardnessHBW 192 max / HRB 90 max (ASTM A213, A249, A269 tubes)
Densityapprox. 8.0 g/cm³

Equivalent Grades

ASTM gradeUNSEN / WerkstoffJIS
TP304S304001.4301 / X5CrNi18-10SUS304
TP304LS304031.4307 / X2CrNi18-9SUS304L
TP316S316001.4401 / X5CrNiMo17-12-2SUS316
TP316LS316031.4404 / X2CrNiMo17-12-2SUS316L

Testing and Inspection

Every lot is tested as required by the ordered standard, with extra tests available at the buyer's request.

  • Hydrostatic or non-destructive electric test: Each length is hydro tested or passes an eddy current or ultrasonic test as permitted by ASTM A312 and A213.
  • Flattening and flaring tests: Confirm ductility of the pipe or tube wall on samples from each lot.
  • Tension and hardness tests: Confirm tensile, yield, elongation and hardness against the standard.
  • Positive material identification: PMI by XRF on every length or on a sampling basis to confirm grade.
  • Intergranular corrosion test: ASTM A262 Practice E available, mainly for L grades and welded fabrications.
  • Third-party inspection: Witness inspection by agencies nominated by the buyer, with EN 10204 3.2 certification.

Mill test certificates list heat number, chemistry, mechanical results and test pressures, and each length is marked with grade, size, standard and heat number for traceability on site.

Why Choose Riyaarth Overseas

Riyaarth Overseas keeps seamless stainless pipes and tubes in the common grades and sizes, and sources other sizes from established Indian and overseas mills. We cut to length, supply EN 10204 3.1 mill test certificates with heat traceability, and pack in wooden boxes or bundles with end caps for export. Send your size list and we will quote quickly.

Applications

Oil and gasInstrument headers, process lines and utility piping on platforms and in gas processing plants.
Chemical processingTransfer lines for acids, solvents and alkalis where a seamless wall is specified for pressure duty.
Power generationSuperheater, reheater and feedwater heater tubes to ASTM A213 in boiler plants.
Heat exchangersShell and tube bundles in refineries and petrochemical units, straight or U-bent.
Pharmaceutical and foodProcess and clean utility lines where a smooth bore and corrosion resistance are needed.
HydraulicsHigh pressure hydraulic and instrumentation lines in machinery and test rigs.

Frequently asked questions

What is the difference between a stainless steel pipe and a tube?

Pipe is specified by nominal pipe size and schedule and is used to carry fluids, mainly to ASTM A312. Tube is specified by exact outside diameter and wall thickness and is used in heat exchangers, boilers and instruments, to standards such as ASTM A213 and A269.

When should seamless be chosen over welded?

Seamless is usually specified for high pressure, high temperature or cyclic service, and where the project code or client specification calls for it. For low and medium pressure lines, welded pipe is often adequate and costs less.

Can seamless pipe be dual certified as 316/316L?

Yes. Material that meets the carbon limit of 316L and the strength of 316 can be certified to both grades on one mill test certificate.

Which standard covers heat exchanger tubes?

Seamless stainless steel heat exchanger, boiler and superheater tubes are covered by ASTM A213 / ASME SA213.