Request Quote
  1. Home
  2. Products
  3. Stainless Steel
  4. Stainless Steel Micro Tubes

Stainless Steel Micro Tubes

Stainless steel micro tubes and capillary tubes in 304 and 316L to ASTM A269, A213 and A632, cut to length, supplied and exported by Riyaarth Overseas.

Stainless Steel Micro Tubes by Riyaarth Overseas

Stainless steel micro tubes, also called capillary tubes, are very small diameter tubes with fine walls, made by repeated cold drawing of seamless or welded tube. They are used where a fluid or gas must be carried in a precise, small bore, or where a fine metal tube is needed for a needle, probe or sensor.

Micro tubes are normally made in 304, 304L, 316 and 316L, to the chemistry and testing of ASTM A269, ASTM A213 or ASTM A632, with dimensions agreed on the purchase order. Riyaarth Overseas supplies and exports stainless micro tubes in coils and straight cut lengths for instrument, medical and laboratory uses.

Key Features

Precise bore: Repeated cold drawing gives a controlled inside diameter for metered flow of liquids and gases.

Fine walls: Thin walls allow small outside diameters while keeping the pressure capacity of stainless steel.

Clean surfaces: Bright annealed or cleaned bores suit analytical and medical applications.

Flexible supply: Available in coils or straight lengths, cut to the length needed by the part.

Specifications

ParameterDetails
StandardsASTM A269, ASTM A213, ASTM A632 (small diameter austenitic tubing), dimensions per purchase order
Grades / UNS304 (S30400), 304L (S30403), 316 (S31600), 316L (S31603)
Outside diameter rangeSmall diameters to order, typically from under 1 mm up to about 6 mm
Wall thickness / scheduleFine walls to order
LengthCoils or straight cut lengths
TypeSeamless or welded and redrawn
EndsPlain end, square cut and deburred
Form / finishRound; bright annealed, hard drawn or polished
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

For micro tubes, state the OD, ID or wall, tolerance, temper (annealed, half hard or hard drawn), length and any cleaning requirement. Tolerances closer than the standard can be agreed with the mill for precision parts.

Chemical Composition

Limits per ASTM A269 for the common micro tube grades.

ElementComposition (%)
Carbon (C)0.08 max (304, 316), 0.035 max (304L, 316L)
Manganese (Mn)2.00 max
Phosphorus (P)0.045 max
Sulphur (S)0.030 max
Silicon (Si)1.00 max
Chromium (Cr)18.0 – 20.0 (304 grades), 16.0 – 18.0 (316 grades)
Nickel (Ni)8.0 – 11.0 (304), 8.0 – 12.0 (304L), 10.0 – 14.0 (316, 316L)
Molybdenum (Mo)2.00 – 3.00 (316 grades)

Mechanical Properties

PropertyValue
Tensile strength, min (annealed)515 MPa (75 ksi) for 304 and 316; 485 MPa (70 ksi) for 304L and 316L (ASTM A213 values)
Yield strength (0.2%), min (annealed)205 MPa (30 ksi) for 304 and 316; 170 MPa (25 ksi) for 304L and 316L (ASTM A213 values)
Elongation in 50 mm, min (annealed)35%
Hardness (annealed)HRB 90 max
Hard drawn conditionHigher strength and hardness, agreed with the buyer

Equivalent Grades

GradeUNSEN / WerkstoffJIS
304S304001.4301SUS304
304LS304031.4307SUS304L
316S316001.4401SUS316
316LS316031.4404SUS316L

For medical uses, the device maker usually specifies the grade by ASTM or ISO medical standards, which may add tighter limits than the general grades above.

Testing and Inspection

Micro tubes are checked closely for size and cleanliness as well as for material grade.

  • Dimensional inspection: OD, ID and wall measured with precision gauges or optical systems.
  • Pressure or leak test: Hydrostatic or pneumatic testing as ordered.
  • Eddy current test: Available for suitable sizes to find surface and near surface defects.
  • Positive material identification: Confirms the grade.
  • Surface and bore cleanliness check: Visual and cleanliness checks for medical and analytical use.
  • Third-party inspection: Available with EN 10204 3.2 certification.

Certificates show heat number, chemistry, temper and dimensional results, and packaging labels carry the same details for traceability down to the coil or box.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources micro tubes from specialist precision tube mills and supplies them in coils or cut lengths with EN 10204 3.1 certificates. Small items are packed in protective tubes or boxes for export. Share your OD, ID, length and quantity and we will send a quick quote.

Applications

Analytical instrumentsChromatography and sampling lines that need a small, clean bore.
Medical devicesNeedle and cannula stock and probe tubes, in grades and finishes agreed with the maker.
Sensors and thermocouplesSheaths and capillaries for temperature and pressure sensors.
Refrigeration and HVACCapillary lines and thermostatic bulb tubes.
ElectronicsFine tubes for dispensing heads and test probes.
Laboratory equipmentGas and liquid transfer lines in test and research rigs.

Frequently asked questions

What is the difference between a micro tube and a capillary tube?

The terms are used for the same product: very small diameter stainless tube with a fine wall, used for precise flow or fine parts.

Which grade is best for micro tubes?

316L is widely used for its corrosion resistance and low carbon. 304 is a lower cost choice where the environment is mild.

Can micro tubes be supplied in coils?

Yes. Micro tubes can be supplied in coils for long continuous lengths or as straight cut pieces.

Which standard covers small diameter stainless tubing?

ASTM A632 covers small diameter seamless and welded austenitic stainless tubing for general service, and ASTM A269 and A213 are also used, with dimensions agreed on the order.