Request Quote
  1. Home
  2. Products
  3. Stainless Steel
  4. Stainless Steel Condenser Tubes

Stainless Steel Condenser Tubes

Stainless steel condenser tubes to ASTM A249, A213 and A268 in 304L, 316L and 439, straight or U-bent, supplied and exported by Riyaarth Overseas.

Stainless Steel Condenser Tubes by Riyaarth Overseas

Stainless steel condenser tubes carry cooling water through surface condensers, feedwater heaters and heat exchangers in power plants, refineries and process industries. They are thin walled, precision tubes ordered by outside diameter and BWG or mm wall, and they must hold close tolerances so they roll tightly into tube sheets.

Welded condenser tubes to ASTM A249 are the most common choice, with seamless tubes to ASTM A213 and ferritic tubes to ASTM A268 used where required. Feedwater heater U-tubes are covered by ASTM A688 for austenitic grades. Riyaarth Overseas supplies and exports stainless steel condenser tubes in straight lengths and U-bent form for new builds and retubing projects.

Key Features

Close tolerances: Tight OD and wall tolerances help ensure leak tight expansion into tube sheets.

Corrosion resistance: 304L and 316L resist fresh and brackish cooling water, and higher grades can be supplied for seawater.

Thin walls: Thin gauges give good heat transfer while keeping the strength of stainless steel.

U-bending: Tubes can be U-bent to the bundle radius, with stress relief of the bends when specified.

Specifications

ParameterDetails
StandardsASTM A249 / ASME SA249 (welded), ASTM A213 / SA213 (seamless), ASTM A268 / SA268 (ferritic), ASTM A688 / SA688 (welded feedwater heater tubes)
Grades / UNS304 (S30400), 304L (S30403), 316 (S31600), 316L (S31603), 439 (S43035), with duplex and super austenitic grades on request
Outside diameter rangeCommonly 15.88 mm (5/8 in) to 50.8 mm (2 in); other sizes to order
Wall thickness / scheduleCommonly BWG 16 to BWG 22, or to order in mm
LengthStraight lengths cut to the bundle size; U-bent tubes to the bundle drawing
TypeWelded and seamless
EndsPlain end, square cut and deburred
Form / finishStraight or U-bent; bright annealed or annealed and pickled
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

For retubing, send the existing tube OD, gauge, length, quantity and tube sheet material. For U-tube bundles, a bend schedule giving the radius and leg length of each row is needed.

Chemical Composition

Limits per ASTM A249 for TP304L and TP316L, the two most ordered condenser tube grades.

ElementComposition (%)
Carbon (C)0.035 max (304L and 316L)
Manganese (Mn)2.00 max
Phosphorus (P)0.045 max
Sulphur (S)0.030 max
Silicon (Si)1.00 max
Chromium (Cr)18.0 – 20.0 (304L), 16.0 – 18.0 (316L)
Nickel (Ni)8.0 – 12.0 (304L), 10.0 – 14.0 (316L)
Molybdenum (Mo)2.00 – 3.00 (316L)

Mechanical Properties

Minimum values per ASTM A249 for annealed tubes. The hardness limit matters for rolling the tube into the tube sheet without cracking.

PropertyValue
Tensile strength, min485 MPa (70 ksi) for TP304L and TP316L
Yield strength (0.2%), min170 MPa (25 ksi) for TP304L and TP316L
Elongation in 50 mm, min35%
Hardness, maxHRB 90 (ASTM A249)

Equivalent Grades

GradeUNSEN / WerkstoffJIS
304LS304031.4307SUS304L
316LS316031.4404SUS316L
439S430351.4510 (closest)n/a

Testing and Inspection

Condenser tubes are tested on every length, as heat exchanger service leaves no room for leaks.

  • Eddy current test: Every tube is tested to ASTM E426 or as specified.
  • Hydrostatic or pneumatic test: Every tube is pressure tested to the standard.
  • Flattening, flange and reverse bend tests: Check the weld and the ductility of the tube.
  • Hardness test: Confirms the tube is soft enough for expansion into tube sheets.
  • U-bend checks: Wall thinning, ovality and bend radius checks on U-bent tubes.
  • Third-party inspection: Witness inspection with EN 10204 3.2 certification.

Each tube is marked with grade, size and heat number, and certificates include eddy current and pressure test results for the whole lot.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies condenser tubes for retubing and new equipment, sourced from established tube mills and cut to the exact bundle length. Every lot is supplied with EN 10204 3.1 certificates, and tubes are packed in wooden boxes with end caps for export. Send your tube sheet details or tube list for a prompt quote.

Applications

Thermal power plantsSteam surface condensers on turbine exhausts.
Feedwater heatersLow and high pressure heaters with U-bent tube bundles.
Refineries and petrochemicalsOverhead condensers and process coolers.
Sugar and distilleriesEvaporators, juice heaters and condensers.
HVAC and refrigerationShell and tube condensers in large chillers.
DesalinationHeat exchanger tubes in thermal desalination plants, in suitable higher grades.

Frequently asked questions

Which standard covers welded stainless condenser tubes?

ASTM A249 / ASME SA249 covers welded austenitic tubes for boilers, superheaters, heat exchangers and condensers. Welded feedwater heater tubes are covered by ASTM A688.

What does BWG mean for condenser tubes?

BWG is the Birmingham Wire Gauge used to state tube wall thickness. For example, BWG 18 is 1.24 mm and BWG 22 is 0.71 mm.

Which grade is best for seawater cooled condensers?

304L and 316L can pit in seawater. Super austenitic grades, super ferritic grades or titanium are usually considered for seawater, depending on design and water quality.

Can condenser tubes be supplied U-bent?

Yes. Tubes can be U-bent to the bundle drawing, with heat treatment of the bends where the specification requires it.