Request Quote
  1. Home
  2. Products
  3. Copper and Brass
  4. ASTM B466 C70600 Copper Nickel Pipes & Tubes

ASTM B466 C70600 Copper Nickel Pipes & Tubes

ASTM B466 C70600 copper nickel seamless pipes and tubes in annealed and light drawn tempers, tested to the standard and supplied by Riyaarth Overseas, Mumbai.

ASTM B466 C70600 Copper Nickel Pipes & Tubes by Riyaarth Overseas

ASTM B466 / ASME SB466 is the standard specification for seamless copper nickel pipe and tube for general engineering use, especially seawater, salt water and process piping. UNS C70600, the 90/10 copper nickel alloy, is the most widely ordered grade under this standard.

B466 sets the chemical limits, tempers, tensile requirements and the tests each lot must pass, such as expansion, flattening and eddy current or hydrostatic testing. It also lets the buyer specify a welding grade with tighter limits on zinc, lead and carbon when the pipe will be fusion welded, which is common in shipbuilding and offshore work.

Riyaarth Overseas supplies and exports ASTM B466 C70600 seamless pipes and tubes, with mill test certificates that report results against each clause of the standard.

Key Features

Defined tempers: B466 C70600 is supplied annealed for bending and expanding, light drawn (H55) for higher strength, or hard drawn where specified, so the temper can be matched to the fabrication route.

Welding grade option: When ordered for welding, zinc is limited to 0.50 max, lead to 0.02 max and carbon to 0.05 max, which reduces the risk of weld cracking.

Lot testing built into the standard: Expansion, flattening and non-destructive testing are part of B466, so each lot is proven before shipment.

Accepted under ASME code: The ASME SB466 equivalent allows the pipe to be used in pressure equipment built to ASME code.

Specifications

ParameterDetails
StandardsASTM B466 / ASME SB466
Grade / UNSUNS C70600 (90/10 copper nickel)
Outside diameter rangeTube from 6.35 mm (1/4 in) OD; pipe NPS 1/8 in upward, sizes on enquiry
Wall thickness / scheduleSCH 10, 40, 80; tube wall in BWG or mm
LengthRandom, fixed and cut lengths
TypeSeamless
EndsPlain ends, bevelled ends
Form / finishRound, U-bent; annealed, light drawn (H55) or hard drawn
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Copper (Cu)Remainder
Nickel (Ni, incl. Co)9.0 – 11.0
Iron (Fe)1.0 – 1.8
Manganese (Mn)1.0 max
Zinc (Zn)1.0 max (0.50 max for welding grade)
Lead (Pb)0.05 max (0.02 max for welding grade)
Carbon (C)0.05 max (welding grade)
Sulphur (S)0.02 max
Phosphorus (P)0.02 max

Mechanical Properties

PropertyValue
Tensile strength, annealed38 ksi (260 MPa) min
Yield strength, annealed13 ksi (90 MPa) min
Tensile strength, light drawn (H55)45 ksi (310 MPa) min
Yield strength, light drawn (H55)35 ksi (240 MPa) min
Density8.94 g/cm³

Yield strength in ASTM B466 is measured at 0.5% extension under load.

Equivalent Grades

StandardDesignation
UNSC70600
ENCW352H, CuNi10Fe1Mn
DIN2.0872
JISC7060
ASMESB466 C70600

Testing and Inspection

ASTM B466 lists the tests required for each lot. Riyaarth Overseas supplies tube with the following results reported:

  • Expansion test: Annealed tube is expanded by 30 percent of its outside diameter without cracking.
  • Flattening test: Specimens are flattened on different axes and must show no cracking visible to the unaided eye.
  • Eddy current test: Required for smaller tube sizes, with calibration notches set by the standard.
  • Hydrostatic test: Tube is pressurised to give a fibre stress of 7000 psi (48 MPa), or pneumatic testing is used where the standard allows.
  • Chemical analysis: Including the welding grade limits where ordered.
  • Third-party inspection: Witness inspection by class societies or agencies on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies ASTM B466 C70600 pipes and tubes from ready stock and from established copper alloy tube mills, in straight lengths, U-bends and cut lengths to suit your bundle or piping layout. Every delivery carries EN 10204 3.1 mill test certificates with heat or lot numbers marked on the tubes.

Please state the temper and whether welding grade is needed when you enquire. Material is packed for export in wooden boxes with end caps, and we send prompt quotations against your tube sheets, bills of materials or specifications.

Applications

Ship seawater systemsWelded seawater mains, ballast and fire lines built from welding grade B466 pipe.
Offshore platformsFire water and seawater cooling piping on fixed and floating installations.
Power plant coolingAuxiliary seawater piping feeding condensers and coolers.
DesalinationBrine and seawater transfer piping in thermal plants.
Process coolingCooling water headers in refineries and chemical plants on the coast.
Hydraulic linesSmall-diameter tube for hydraulic and instrument lines in marine service.

Frequently asked questions

What does ASTM B466 cover?

ASTM B466 covers seamless copper nickel pipe and tube for general engineering use, including alloys C70400, C70600 and C71500.

What is the welding grade under ASTM B466?

When the purchaser specifies tube for welding, zinc is limited to 0.50 max, lead to 0.02 max and carbon to 0.05 max to improve weldability.

What is the difference between ASTM B466 and ASTM B111?

ASTM B466 covers seamless pipe and tube for general piping, while ASTM B111 covers seamless tubes specifically for condensers, evaporators and heat exchangers.

What tempers are available in B466 C70600?

Pipe and tube are supplied annealed, light drawn (H55) or hard drawn, depending on the strength and formability needed.