Request Quote
  1. Home
  2. Products
  3. Copper and Brass
  4. ASTM B466 C71500 Copper Nickel Pipes & Tubes

ASTM B466 C71500 Copper Nickel Pipes & Tubes

ASTM B466 C71500 (70/30) copper nickel seamless pipes and tubes for high-velocity seawater and condenser service, tested to standard by Riyaarth Overseas.

ASTM B466 C71500 Copper Nickel Pipes & Tubes by Riyaarth Overseas

ASTM B466 / ASME SB466 covers seamless copper nickel pipe and tube for general engineering service. Under this standard, UNS C71500 is the 70/30 copper nickel grade, with 29 to 33 percent nickel and 0.40 to 1.0 percent iron. It is used where 90/10 would be limited by flow velocity, pressure or erosion.

B466 C71500 is normally supplied annealed, with drawn tempers available when higher strength is needed. The standard sets tensile requirements, lot tests and the optional welding grade with tighter limits on zinc, lead and carbon for pipe that will be fusion welded.

Riyaarth Overseas supplies and exports ASTM B466 C71500 seamless pipes and tubes to naval, power and offshore projects, with test results reported against the standard.

When placing an order to B466, buyers should state the alloy, temper, size as NPS and schedule or OD and wall, length, quantity and whether welding grade is required. Optional requirements such as a specific non-destructive test, third-party witness or special packing should also be named in the order, since the standard lists them as supplementary items agreed between purchaser and supplier.

Key Features

Higher strength than C70600: At annealed tensile strength of 52 ksi min, C71500 is notably stronger than C70600, allowing higher design pressures for the same wall.

Erosion and impingement resistance: The higher nickel content gives better resistance to turbulent, high-velocity seawater.

Welding grade option: Pipe for fusion welding can be ordered with zinc 0.50 max, lead 0.02 max and carbon 0.05 max.

ASME code acceptance: ASME SB466 C71500 can be used in pressure equipment built to ASME code.

Specifications

ParameterDetails
StandardsASTM B466 / ASME SB466
Grade / UNSUNS C71500 (70/30 copper nickel)
Outside diameter rangeTube from 6.35 mm (1/4 in) OD; pipe sizes on enquiry
Wall thickness / scheduleSCH 10, 40, 80; tube wall in BWG or mm
LengthRandom, fixed and cut lengths
TypeSeamless
EndsPlain ends, bevelled ends
Form / finishRound, U-bent; annealed or drawn
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Copper (Cu)Remainder
Nickel (Ni, incl. Co)29.0 – 33.0
Iron (Fe)0.40 – 1.0
Manganese (Mn)1.0 max
Zinc (Zn)1.0 max (0.50 max for welding grade)
Lead (Pb)0.05 max (0.02 max for welding grade)
Carbon (C)0.05 max (welding grade)
Sulphur (S)0.02 max
Phosphorus (P)0.02 max

Mechanical Properties

PropertyValue
Tensile strength, annealed52 ksi min
Yield strength, annealed18 ksi (125 MPa) min
Density8.95 g/cm³

Yield strength in ASTM B466 is measured at 0.5% extension under load. Drawn tempers have higher minimums, agreed at order.

Equivalent Grades

StandardDesignation
UNSC71500
ENCW354H, CuNi30Mn1Fe
DIN2.0882
JISC7150
ASMESB466 C71500

Testing and Inspection

Each lot of ASTM B466 C71500 pipe and tube is tested as the standard requires, and results are reported on the mill certificate:

  • Expansion test: Annealed tube is expanded by 30 percent of its outside diameter without cracking.
  • Flattening test: Specimens flattened on different axes must show no visible cracks.
  • Eddy current test: Applied to smaller tube sizes using the calibration notches set by the standard.
  • Hydrostatic test: Pressure test to a fibre stress of 7000 psi (48 MPa), or pneumatic test where allowed.
  • Chemical analysis: Nickel, iron, manganese and welding grade limits where ordered.
  • Third-party inspection: Witness inspection on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies ASTM B466 C71500 pipes and tubes from ready stock and from established copper alloy tube mills, in straight lengths, U-bends and cut lengths to suit your bundle or piping layout. Every delivery carries EN 10204 3.1 mill test certificates with heat or lot numbers marked on the tubes.

Please state the temper and whether welding grade is needed when you enquire. Material is packed for export in wooden boxes with end caps, and we send prompt quotations against your tube sheets, bills of materials or specifications.

Applications

Naval seawater systemsHigh-velocity seawater piping on warships and submarines.
Power station condensersInlet sections and high-flow cooling water lines.
Offshore platformsSeawater cooling and injection systems with high flow rates.
DesalinationHeat recovery and brine lines in thermal desalination plants.
Steam cyclesFeedwater and condensate piping where ammonia is present.
Chemical plantsCooling water headers using polluted or brackish water.

Frequently asked questions

Why choose C71500 over C70600 under ASTM B466?

C71500 has higher strength and better resistance to erosion and impingement, so it is used where seawater velocities or pressures are higher than 90/10 can handle.

Is C71500 pipe available for welding?

Yes. B466 allows the buyer to order a welding grade with zinc 0.50 max, lead 0.02 max and carbon 0.05 max.

What tests does ASTM B466 require?

B466 requires expansion or flattening tests, eddy current or hydrostatic testing, chemical analysis and tensile testing to confirm each lot.

Can C71500 tubes be supplied U-bent?

Yes. Riyaarth Overseas can supply C71500 tubes U-bent to your bend schedule, with test certificates for each lot.