Request Quote
  1. Home
  2. Products
  3. Copper and Brass
  4. Copper Nickel 95/5 Tubes (UNS C70400)

Copper Nickel 95/5 Tubes (UNS C70400)

Copper Nickel 95/5 tubes, UNS C70400, to ASTM B111 and B466 for condensers, coolers and seawater lines, supplied and exported by Riyaarth Overseas.

Copper Nickel 95/5 Tubes (UNS C70400) by Riyaarth Overseas

Copper Nickel 95/5, UNS C70400, contains about 5 percent nickel with iron and manganese additions. It sits between admiralty brass and 90/10 copper nickel: it offers better resistance to seawater and to dezincification than brasses, at a lower nickel content and cost than 90/10.

C70400 tubes are produced to ASTM B111 for condenser and heat exchanger tubes and to ASTM B466 for seamless tube, with the matching ASME SB numbers. They are supplied in the annealed condition for expanding and bending, or light drawn for higher strength.

Riyaarth Overseas supplies and exports Copper Nickel 95/5 tubes for heat exchangers, coolers and marine tubing.

C70400 is a good choice for retubing coolers that were originally fitted with admiralty or aluminium brass, where some extra corrosion margin is wanted without moving to the cost of 90/10. As with other copper nickel tubes, the protective film forms best when the unit is first commissioned with clean, aerated water, and long periods of stagnant or sulphide-polluted water should be avoided. When enquiring, please give the standard, temper, OD, wall, length and the bend schedule for any U-tubes.

Key Features

Balanced cost and performance: The 5 percent nickel content gives useful seawater resistance at a lower alloy cost than 90/10 copper nickel.

No dezincification: C70400 contains no deliberate zinc, so it does not suffer the dezincification that can affect brass tubes.

High thermal conductivity: Lower nickel than 90/10 means higher thermal conductivity, which helps heat transfer in coolers and condensers.

Good formability: Annealed tube expands into tube sheets and bends readily into U-tubes.

Specifications

ParameterDetails
StandardsASTM B111 / ASME SB111, ASTM B466 / ASME SB466
Grade / UNSCopper Nickel 95/5, UNS C70400
Outside diameter rangeTube from 6.35 mm (1/4 in) OD; sizes on enquiry
Wall thickness / scheduleBWG or mm as ordered
LengthStraight, fixed and cut lengths
TypeSeamless
EndsPlain ends
Form / finishStraight and U-bent tube; annealed (O61) or light drawn (H55)
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Copper (Cu)Remainder
Nickel (Ni, incl. Co)4.8 – 6.2
Iron (Fe)1.3 – 1.7
Manganese (Mn)0.30 – 0.8
Zinc (Zn)1.0 max
Lead (Pb)0.05 max

Mechanical Properties

PropertyValue
Tensile strength (ASTM B111, annealed O61)38 ksi (260 MPa) min
Yield strength (ASTM B111, annealed O61)12 ksi (85 MPa) min
Tensile strength (light drawn H55)40 ksi (275 MPa) min
Yield strength (light drawn H55)30 ksi (205 MPa) min

Equivalent Grades

UNS C70400 has no widely used direct equivalent in the current EN or JIS tube standards. It is usually ordered by its UNS number to ASTM B111 or B466, and is sometimes described as CuNi5Fe.

Testing and Inspection

C70400 tubes are inspected to ASTM B111 or B466 as ordered. Typical checks include:

  • Eddy current test: Every tube is tested for wall defects.
  • Hydrostatic or pneumatic test: Where specified as an alternative or addition.
  • Expansion and flattening tests: Ductility checks on samples from each lot.
  • Residual stress test: Mercurous nitrate or ammonia vapour test where required for drawn tube.
  • Dimensional and visual inspection: OD, wall, length and surface.
  • Third-party inspection: Witness inspection on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Copper Nickel 95/5 tubes from ready stock and from established copper alloy tube mills, in straight lengths, U-bends and cut lengths to suit your bundle or piping layout. Every delivery carries EN 10204 3.1 mill test certificates with heat or lot numbers marked on the tubes.

We can advise on whether 95/5, 90/10 or aluminium brass suits your cooling water conditions. Material is packed for export in wooden boxes with end caps, and we send prompt quotations against your tube sheets, bills of materials or specifications.

Applications

Heat exchangersTube bundles in shell and tube exchangers cooled by clean seawater or brackish water.
Lube oil and jacket water coolersEngine and compressor coolers on ships and in power plants.
CondensersSurface condenser tubes where 90/10 is not required by the specification.
Marine engineeringSmall-bore seawater and instrument tubing on board ships.
Refrigeration and HVACWater-cooled condensers in chillers using cooling tower or brackish water.
Feedwater heatersLow-pressure heater tubing in steam cycles.

Frequently asked questions

What is UNS C70400?

UNS C70400 is a copper nickel alloy with about 5 percent nickel and small additions of iron and manganese, commonly called 95/5 copper nickel.

Which standards cover C70400 tubes?

Condenser and heat exchanger tubes are made to ASTM B111 / ASME SB111, and seamless tube to ASTM B466 / ASME SB466.

How does 95/5 compare with 90/10 copper nickel?

95/5 has less nickel, so it costs less and conducts heat better, while 90/10 has better seawater and erosion resistance and is preferred for main seawater piping.

In what tempers are C70400 tubes supplied?

They are normally supplied annealed (O61) for expanding and bending, or light drawn (H55) where higher strength is needed.