
EN 10216-2 16Mo3 Pipes & Tubes
EN 10216-2 16Mo3 (1.5415) seamless pipes and tubes for boilers, superheaters and pressure piping, supplied by Riyaarth Overseas with EN 10204 3.1 MTC.

EN 10216-2 16Mo3 pipes and tubes are seamless carbon-molybdenum steel tubes made for pressure service at elevated temperatures. EN 10216-2 is the European standard for non-alloy and alloy steel seamless tubes with specified elevated temperature properties, and 16Mo3 (steel number 1.5415) is one of its most widely used grades. The roughly 0.3% molybdenum addition raises creep strength above that of plain carbon steels such as P235GH and P265GH, while the steel stays easy to weld and form.
Boiler makers, heat recovery steam generator builders and refinery contractors specify 16Mo3 for superheater and economiser tubes, headers and hot process lines where temperatures are too high for carbon steel but the duty does not yet call for chromium-molybdenum grades such as 13CrMo4-5 or 10CrMo9-10. Riyaarth Overseas supplies and exports EN 10216-2 16Mo3 pipes and tubes in the normalised condition from approved mills, with full traceability and test documentation.
Key Features
Creep resistance: Molybdenum in the 0.25 – 0.35% range improves strength under sustained load at elevated temperature, which is why 16Mo3 is used in boiler pressure parts.
Normalised delivery: Tubes are delivered in the normalised (+N) condition, giving a uniform fine-grained structure and consistent tensile and impact values along the length.
Good weldability: With carbon limited to 0.20% max, 16Mo3 welds with standard procedures; preheat and post-weld heat treatment are set by wall thickness and the applicable design code.
Pressure equipment compliance: EN 10216-2 sets test categories (TC1 and TC2), leak testing and impact requirements, making the tubes suitable for equipment built under the European Pressure Equipment Directive.
Specifications
| Parameter | Details |
|---|---|
| Standard | EN 10216-2 (seamless steel tubes for pressure purposes, elevated temperature properties) |
| Grade / steel number | 16Mo3 / 1.5415 |
| Outside diameter range | Dimensions to EN 10220, from small-bore boiler tube to large-bore pipe, as per enquiry |
| Wall thickness | As per EN 10220 or as ordered |
| Length | Single random, double random, fixed and cut lengths |
| Type | Seamless, hot-finished or cold-finished |
| Delivery condition | Normalised (+N) |
| Ends | Plain end or bevelled end |
| Form / finish | Round pipe and tube; black, varnished or oiled surface |
| Test certificate | EN 10204 3.1 or 3.2 |
Chemical Composition
| Element | Composition (%) |
|---|---|
| Carbon (C) | 0.12 – 0.20 |
| Silicon (Si) | 0.35 max |
| Manganese (Mn) | 0.40 – 0.90 |
| Phosphorus (P) | 0.025 max |
| Sulphur (S) | 0.020 max |
| Chromium (Cr) | 0.30 max |
| Molybdenum (Mo) | 0.25 – 0.35 |
| Nickel (Ni) | 0.30 max |
| Copper (Cu) | 0.30 max |
Mechanical Properties
| Property | Value |
|---|---|
| Tensile strength (Rm) | 450 – 600 MPa |
| Yield strength (ReH), wall up to 16 mm | 280 MPa min |
| Elongation (A), longitudinal | 22% min |
| Elongation (A), transverse | 20% min |
| Density | 7.85 g/cm³ |
Yield strength minimums reduce for heavier walls as set out in EN 10216-2. Elevated temperature proof strength values are also tabulated in the standard for design.
Equivalent Grades
| Standard / system | Designation |
|---|---|
| EN steel number | 1.5415 |
| Former DIN (DIN 17175) | 15Mo3 (predecessor grade) |
| ASTM / ASME (comparable C-0.5Mo) | A335 / SA335 P1, A209 / SA209 T1 (UNS K11522) |
The ASTM grades are comparable carbon-molybdenum steels, not exact equivalents; chemistry and test requirements differ, so substitution should be confirmed against the design code.
Testing and Inspection
Every tube is tested as required by EN 10216-2 for the ordered test category, and further tests can be added at the time of order.
- Chemical analysis (cast and product) and tensile testing
- Impact testing at the temperatures set in the standard
- Leak tightness test by hydrostatic test or eddy current testing
- Ultrasonic testing for longitudinal imperfections for test category 2
- Flattening or ring expanding tests, dimensional and visual inspection
- Positive material identification (PMI) and third-party inspection by TÜV, BV, Lloyd's or the client's agency on request
Why Choose Riyaarth Overseas
Riyaarth Overseas sources EN 10216-2 16Mo3 tubes from established mills and keeps stock of common boiler sizes for quick dispatch. We supply cut lengths, bevelled ends and EN 10204 3.1 mill test certificates, with 3.2 available through third-party inspection on request. Tubes are bundled or crated for export with end caps and marking for traceability, and we reply to enquiries with a clear quotation and delivery time.
Applications






Frequently asked questions
What is 16Mo3 steel?
16Mo3 (1.5415) is a carbon-molybdenum steel with about 0.3% molybdenum. It is used for pressure parts that operate at elevated temperatures, mainly boiler and heat exchanger tubes.
What is the difference between 16Mo3 and P265GH?
P265GH is a non-alloy carbon steel. 16Mo3 adds molybdenum, which gives higher creep and elevated temperature strength, so it is used where metal temperatures are higher.
Is 16Mo3 the same as ASTM A335 P1?
They are comparable carbon-molybdenum steels but not identical. Chemistry limits and test requirements differ, so the design engineer should approve any substitution.
In what condition are EN 10216-2 16Mo3 tubes supplied?
They are supplied in the normalised (+N) condition, with test certificates to EN 10204 3.1, or 3.2 when third-party inspection is ordered.
