Request Quote
  1. Home
  2. Products
  3. Alloy Steel
  4. EN8 Seamless Pipes

EN8 Seamless Pipes

EN8 (080M40) medium carbon steel seamless pipes and hollow tubes for shafts, bushes and machined parts, supplied by Riyaarth Overseas with 3.1 certificates.

EN8 Seamless Pipes by Riyaarth Overseas

EN8 seamless pipes are hollow sections made from EN8, the British Standard BS 970 designation for 080M40 medium carbon steel. EN8 is an unalloyed steel with about 0.40% carbon. It offers higher strength than mild steel, machines well and can be flame or induction hardened on the surface. Seamless pipe in this grade is used as mechanical tubing and hollow bar rather than as pressure piping.

Engineering workshops choose EN8 tube for bushes, sleeves, rollers, shafts and spacers where solid bar would waste material. Riyaarth Overseas supplies and exports EN8 seamless pipes in hot-finished and cold-drawn forms, in normalised or hardened and tempered condition, cut to length for machining.

Key Features

Medium carbon strength: Around 0.40% carbon gives tensile strength of 550 MPa min in the normalised condition, well above mild steel tube.

Surface hardening: EN8 can be flame or induction hardened to give a wear-resistant surface over a tough core.

Good machinability: The grade turns, bores and threads well, which suits high-volume machined parts.

Material savings: Seamless hollow sections cut drilling time and scrap compared with machining parts from solid bar.

Specifications

ParameterDetails
StandardBS 970 080M40 (EN8)
GradeEN8 / 080M40
Outside diameter rangeAs per mill availability and enquiry
Wall thicknessMedium to heavy wall for machining allowance
LengthRandom lengths and cut pieces
TypeSeamless, hot-finished or cold-drawn
ConditionNormalised, or hardened and tempered
EndsPlain, square cut
Form / finishRound hollow tube; black, descaled or bright surface
Test certificateEN 10204 3.1

EN8 seamless tube is bought by outside diameter and inside diameter or wall thickness, with a machining allowance on both surfaces. Hot-finished tube has a scaled surface and wider tolerances, so it suits parts that are machined all over. Cold-drawn tube has a closer tolerance and smoother finish, which reduces machining on bushes and sleeves.

Normalised EN8 is the usual starting condition for general machining. Where higher strength is needed through the section, the tube can be ordered hardened and tempered. For parts that need wear resistance only at the surface, normalised tube is machined first and then flame or induction hardened locally.

EN8 is not a pressure piping material. If the tube will carry fluid under pressure, choose a grade made to a pressure standard, such as ASTM A106 Grade B or EN 10216-1 P235TR2, so that hydrostatic testing and design code acceptance are covered.

Chemical Composition

ElementComposition (%)
Carbon (C)0.36 – 0.44
Silicon (Si)0.10 – 0.40
Manganese (Mn)0.60 – 1.00
Sulphur (S)0.050 max
Phosphorus (P)0.050 max

Mechanical Properties

PropertyValue (normalised)
Tensile strength550 MPa min
Yield strength280 MPa min
Elongation16% min
Hardness152 – 207 HB
Density7.85 g/cm³

Values apply to the normalised condition in smaller ruling sections; hardened and tempered material reaches higher strength, agreed at order.

Equivalent Grades

Standard / systemDesignation
BS 970080M40
EN 10083-2C40 (1.0511)
AISI / SAE1040
JIS G4051S40C
IS 157040C8

These are the commonly accepted near equivalents; limits differ slightly between standards.

Testing and Inspection

Tubes are inspected against the order and grade requirements before dispatch.

  • Chemical analysis by heat
  • Tensile and hardness testing in the delivered condition
  • Ultrasonic testing for internal defects on request
  • Positive material identification (PMI)
  • Dimensional, ovality and straightness checks
  • Third-party inspection on request

Why Choose Riyaarth Overseas

Riyaarth Overseas sources EN8 seamless tube from reliable mills and supplies it cut to your lengths with machining allowance in mind. Each lot comes with EN 10204 3.1 certificates showing heat number, chemistry and mechanical results. We pack for road or sea freight and reply to enquiries with quick, clear quotations.

Applications

General engineeringBushes, sleeves, spacers and collars machined from hollow stock.
AutomotiveShafts, axles and hubs where moderate strength and surface hardening are needed.
Material handlingConveyor rollers and idler shells that benefit from a hard-wearing surface.
HydraulicsLow-pressure cylinder sleeves and gland parts that are not pressure-code items.
Agricultural machineryPivot pins, hollow shafts and couplings.
Textile and printing machineryRollers and spindle tubes machined to close tolerance.

Frequently asked questions

Is EN8 an alloy steel?

No. EN8 (080M40) is an unalloyed medium carbon steel with about 0.40% carbon. It is often grouped with engineering steels because it is used for machined parts.

Can EN8 seamless pipe be used for pressure service?

EN8 tube is mechanical tubing and is not made to a pressure piping code. For pressure lines use grades such as ASTM A106 or EN 10216-2.

What is the equivalent of EN8?

Common near equivalents are C40 (1.0511), AISI 1040, JIS S40C and IS 1570 40C8.

Can EN8 tube be hardened?

Yes. EN8 can be hardened and tempered, or flame and induction hardened on the surface for wear resistance.