Request Quote
  1. Home
  2. Products
  3. Alloy Steel
  4. EN9 Seamless Pipes

EN9 Seamless Pipes

EN9 (070M55) seamless pipes and hollow sections in 0.55% carbon steel for wear-resistant rollers, sleeves and machine parts, supplied by Riyaarth Overseas.

EN9 Seamless Pipes by Riyaarth Overseas

EN9 seamless pipes are hollow sections in EN9, the BS 970 designation for 070M55 medium-high carbon steel. With carbon between 0.50 and 0.60%, EN9 is harder and more wear resistant than EN8, and it responds well to flame and induction hardening. Like EN8, it is unalloyed and is used as mechanical tubing for machined parts, not for pressure piping.

EN9 tube is chosen for sprockets, rollers, wear sleeves and other components where the surface must resist abrasion while the core stays tough. Riyaarth Overseas supplies and exports EN9 seamless pipes in hot-finished and cold-drawn forms, cut to size and in the condition required for your machining and heat treatment route.

Key Features

Higher carbon content: About 0.55% carbon gives higher strength and hardness than EN8 in the normalised condition.

Wear resistance: The grade hardens well at the surface by flame or induction, giving long life in rubbing and rolling contact.

Machinable before hardening: In the normalised or annealed state EN9 can be turned and bored, then surface hardened in the final step.

Hollow stock efficiency: Seamless tube reduces boring time and scrap for ring-shaped and sleeve parts.

Specifications

ParameterDetails
StandardBS 970 070M55 (EN9)
GradeEN9 / 070M55
Outside diameter rangeAs per mill availability and enquiry
Wall thicknessMedium to heavy wall
LengthRandom lengths and cut pieces
TypeSeamless, hot-finished or cold-drawn
ConditionNormalised, annealed, or hardened and tempered
EndsPlain, square cut
Form / finishRound hollow tube; black or descaled surface
Test certificateEN 10204 3.1

EN9 tube is normally ordered in the normalised condition for machining, with sizes stated as outside diameter and inside diameter including a machining allowance. Hot-finished tube suits parts that are machined all over, while cold-drawn tube gives a closer starting tolerance for bushes and sleeves.

The higher carbon content of EN9 makes it more sensitive to cracking during welding and quenching than EN8. Heat treatment shops usually prefer flame or induction hardening of the working surface, which gives a hard, wear-resistant case while the core stays tougher. Through hardening is possible in thinner sections, followed by tempering to the required hardness.

Because EN9 is a mechanical tube grade, it is not used for pressure piping. For pressure lines, use a code-listed pipe grade. For higher strength with better toughness than EN9, a low alloy steel such as EN19 (709M40) or 4140 is often a better choice.

Chemical Composition

ElementComposition (%)
Carbon (C)0.50 – 0.60
Silicon (Si)0.10 – 0.40
Manganese (Mn)0.50 – 0.90
Sulphur (S)0.050 max
Phosphorus (P)0.050 max

Mechanical Properties

PropertyValue
Tensile strength, normalised (smaller ruling sections)700 MPa min
Density7.85 g/cm³

Yield, elongation and hardness depend on section size and heat treatment, and are confirmed on the mill test certificate for the condition ordered.

Equivalent Grades

Standard / systemDesignation
BS 970070M55
EN 10083-2C55 (1.0535)
AISI / SAE1055
JIS G4051S55C
IS 157055C8

These are near equivalents; check exact limits where the specification is strict.

Testing and Inspection

Each lot is checked to the grade and order requirements.

  • Chemical analysis by heat
  • Tensile and hardness testing in the supplied condition
  • Ultrasonic testing on request
  • Positive material identification (PMI)
  • Dimensional and visual inspection
  • Third-party inspection on request

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies EN9 seamless tube from trusted mills, cut to the lengths your parts require. Material comes with EN 10204 3.1 certificates for traceability, and we pack bundles securely for domestic and export shipment. Share your sizes and we will send a prompt quotation with delivery time.

Applications

Power transmissionSprocket hubs, gear blanks and couplings that are surface hardened.
ConveyorsRollers, sleeves and bushes running in abrasive conditions.
Agricultural equipmentWear sleeves, hollow pins and tillage component bodies.
Machine toolsSpindle sleeves, guide bushes and collars.
Mining and quarryingWear rings and spacers in crushers and screens.
AutomotiveHollow shafts and wear parts that need induction hardening.

Frequently asked questions

What is the difference between EN8 and EN9?

EN9 has higher carbon (0.50 – 0.60%) than EN8 (0.36 – 0.44%), so it is harder and more wear resistant but slightly less ductile.

Is EN9 an alloy steel?

No. EN9 (070M55) is an unalloyed medium-high carbon steel.

What is the equivalent of EN9?

Near equivalents are C55 (1.0535), AISI 1055, JIS S55C and IS 1570 55C8.

Can EN9 seamless pipe be welded?

Welding is possible but needs preheat and controlled cooling because of the higher carbon content. Most EN9 parts are machined and surface hardened rather than welded.