Request Quote
  1. Home
  2. Products
  3. Inconel
  4. Incoloy 800 Pipes & Tubes

Incoloy 800 Pipes & Tubes

Incoloy 800 (UNS N08800) nickel-iron-chromium pipes and tubes to ASTM B407, B163 and B514 for heat exchangers and oxidation service, from Riyaarth Overseas.

Incoloy 800 Pipes & Tubes by Riyaarth Overseas

Incoloy 800 pipes and tubes are made from a nickel-iron-chromium alloy, UNS N08800 (Werkstoff 1.4876), with 30 – 35% nickel and 19 – 23% chromium. The alloy resists oxidation and carburisation at elevated temperature and stays stable in long service, without forming the brittle sigma phase that can affect stainless steels. Seamless pipe and tube are made to ASTM B407, heat exchanger tube to ASTM B163, and welded pipe and tube to ASTM B514 and B515.

Incoloy 800 is normally supplied in the cold-worked annealed condition and is used mainly for service up to about 600 °C, where its strength and corrosion resistance suit heat exchangers, process piping and steam generator tubes. For creep-limited service above that range, the 800H and 800HT versions are used. Riyaarth Overseas supplies and exports Incoloy 800 pipes and tubes from established mills.

Key Features

Balanced corrosion resistance: The nickel and chromium content gives resistance to oxidising and reducing media and to chloride stress corrosion cracking better than standard austenitic stainless steels.

Oxidation and carburisation resistance: The alloy forms a protective oxide in hot air and resists carbon pick-up in hydrocarbon atmospheres.

Structural stability: Long exposure at elevated temperature does not cause sigma phase embrittlement.

Fabrication: The annealed alloy bends, expands and welds well, which suits heat exchanger manufacture.

Specifications

ParameterDetails
StandardsASTM B407 / ASME SB407 (seamless pipe and tube), B163 / SB163 (heat exchanger tube), B514 (welded pipe), B515 (welded tube)
Grade / UNSIncoloy 800 / UNS N08800
Outside diameter rangeSmall-bore tube to NPS pipe sizes, as per enquiry
Wall thickness / scheduleSCH 5S, 10S, 40S, 80S, 160 or tube gauge
LengthRandom, fixed and cut lengths; U-bent tubes on request
TypeSeamless, welded
ConditionCold-worked annealed or hot-finished annealed
EndsPlain end, bevelled end
Form / finishRound pipe and tube, pickled or bright annealed
Test certificateEN 10204 3.1 or 3.2

Incoloy 800 is the right choice when the service temperature is moderate and good corrosion resistance and fabrication are the main needs. If design is controlled by creep at higher temperature, specify 800H or 800HT, which have controlled carbon, a higher annealing temperature and a coarse grain size.

For heat exchanger tubes, order to ASTM B163 in the cold-worked annealed condition, which suits tube expansion and U-bending. For process piping, ASTM B407 pipe in standard schedules is used, with welded pipe to ASTM B514 as an option in larger sizes.

Chemical Composition

ElementComposition (%)
Nickel (Ni)30.0 – 35.0
Chromium (Cr)19.0 – 23.0
Iron (Fe)39.5 min
Carbon (C)0.10 max
Manganese (Mn)1.50 max
Silicon (Si)1.00 max
Sulphur (S)0.015 max
Copper (Cu)0.75 max
Aluminium (Al)0.15 – 0.60
Titanium (Ti)0.15 – 0.60

Mechanical Properties

Property (ASTM B407)Cold-worked annealedHot-finished or hot-finished annealed
Tensile strength, min520 MPa (75 ksi)450 MPa (65 ksi)
Yield strength (0.2%), min205 MPa (30 ksi)170 MPa (25 ksi)
Elongation, min30%30%
Physical propertyValue
Density7.94 g/cm³
Melting range1357 – 1385 °C

Equivalent Grades

Standard / systemDesignation
UNSN08800
Werkstoff Nr.1.4876
ENX10NiCrAlTi32-21
JISNCF 800
Common namesAlloy 800

Testing and Inspection

Each length is tested to the ASTM standard ordered, and extra tests can be specified.

  • Chemical analysis and tensile testing
  • Hydrostatic test or eddy current test on every length
  • Flattening and flaring tests
  • Intergranular corrosion testing where specified
  • Positive material identification (PMI)
  • Dimensional, visual and third-party inspection

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Incoloy 800 pipes and tubes from reliable nickel alloy mills and stock, cut to the lengths or U-bends you need. We provide EN 10204 3.1 certificates with full traceability and pack in wooden cases for export. Share your sizes and quantities for a quick quotation.

Applications

Heat exchangersTube bundles in chemical and petrochemical exchangers handling hot corrosive fluids.
Power generationSteam generator tubing and superheater parts at moderate high temperature.
Chemical processingProcess piping where chloride stress corrosion cracking is a risk for stainless steel.
Heat treatmentFurnace components, retorts and muffles in carburising atmospheres.
Domestic and industrial heatingSheathing for electric heating elements.
Pulp and paperDigester heating tubes and liquor heaters.

Frequently asked questions

What is Incoloy 800 used for?

It is used for heat exchangers, process piping, steam generator tubing, furnace parts and heating element sheaths.

What is the difference between Incoloy 800 and 800H?

Incoloy 800H has controlled carbon (0.05 – 0.10%), a higher annealing temperature and a coarse grain size, which give better creep strength above about 600 °C.

Which ASTM standard covers Incoloy 800 seamless pipe?

ASTM B407 covers seamless pipe and tube, and ASTM B163 covers condenser and heat exchanger tubes.

Is Incoloy 800 an Inconel alloy?

No. Incoloy 800 is a nickel-iron-chromium alloy with iron as the main element, while Inconel alloys are nickel-chromium based.