Request Quote
  1. Home
  2. Products
  3. Inconel
  4. Incoloy 800H Pipes & Tubes

Incoloy 800H Pipes & Tubes

Incoloy 800H (UNS N08810) pipes and tubes to ASTM B407, with controlled carbon and coarse grain for creep strength in furnaces, from Riyaarth Overseas.

Incoloy 800H Pipes & Tubes by Riyaarth Overseas

Incoloy 800H pipes and tubes are made from the high-temperature version of Incoloy 800, UNS N08810 (Werkstoff 1.4958). The chemistry stays within the Incoloy 800 range, but carbon is controlled to 0.05 – 0.10%, and the material is solution annealed at 1121 °C (2050 °F) minimum to give an average grain size of ASTM No. 5 or coarser. Together these controls give much higher creep and stress rupture strength.

Because of this, Incoloy 800H is used in hot process plant above about 600 °C, such as steam methane reformer outlet systems, ethylene furnace parts and high-temperature heat exchangers. It is listed in the ASME Boiler and Pressure Vessel Code for elevated temperature design. Riyaarth Overseas supplies and exports Incoloy 800H seamless and welded pipes and tubes with full test records.

Key Features

Creep and rupture strength: Controlled carbon and coarse grain size raise creep strength well above that of standard Incoloy 800 at high temperature.

Solution annealed: A minimum annealing temperature of 1121 °C dissolves carbides and develops the grain structure needed for creep service.

Oxidation and carburisation resistance: High nickel and chromium protect the tube in hot oxidising and carburising process gases.

Code recognition: Incoloy 800H is covered by ASME code allowable stresses for elevated temperature pressure design.

Specifications

ParameterDetails
StandardsASTM B407 / ASME SB407 (seamless pipe and tube), B163 / SB163 (heat exchanger tube), B514 (welded pipe), B515 (welded tube)
Grade / UNSIncoloy 800H / UNS N08810
Outside diameter rangeSmall-bore tube to NPS pipe sizes, as per enquiry
Wall thickness / scheduleSCH 5S, 10S, 40S, 80S, 160 or tube gauge
LengthRandom, fixed and cut lengths; U-bent tubes on request
TypeSeamless, welded
ConditionSolution annealed at 1121 °C (2050 °F) min, grain size ASTM No. 5 or coarser
EndsPlain end, bevelled end
Form / finishRound pipe and tube, pickled or bright annealed
Test certificateEN 10204 3.1 or 3.2

Incoloy 800H tubes and pipes should be ordered with the grain size and annealing temperature stated on the certificate, since these are what separate 800H from standard 800. If the design calls for the best available creep life, consider 800HT, which adds tighter limits on aluminium and titanium.

For welded construction, matching filler metals designed for elevated temperature service are used, and the weld procedure should be qualified for the expected temperature range.

Chemical Composition

ElementComposition (%)
Nickel (Ni)30.0 – 35.0
Chromium (Cr)19.0 – 23.0
Iron (Fe)39.5 min
Carbon (C)0.05 – 0.10
Manganese (Mn)1.50 max
Silicon (Si)1.00 max
Sulphur (S)0.015 max
Copper (Cu)0.75 max
Aluminium (Al)0.15 – 0.60
Titanium (Ti)0.15 – 0.60

Mechanical Properties

Property (ASTM B407)Value
Tensile strength, min450 MPa (65 ksi)
Yield strength (0.2%), min170 MPa (25 ksi)
Elongation, min30%
Density7.94 g/cm³
Melting range1357 – 1385 °C

Room temperature minimums are lower than for cold-worked Incoloy 800 because of the coarse grain, but strength at high temperature is higher.

Equivalent Grades

Standard / systemDesignation
UNSN08810
Werkstoff Nr.1.4958
ENX5NiCrAlTi31-20
JISNCF 800H
Common namesAlloy 800H

Testing and Inspection

In addition to standard tests, 800H orders include checks that confirm its high-temperature condition.

  • Chemical analysis with carbon, aluminium and titanium confirmed
  • Grain size measurement (ASTM No. 5 or coarser)
  • Tensile testing and flattening or flaring tests
  • Hydrostatic test or eddy current test on every length
  • Positive material identification (PMI)
  • Dimensional, visual and third-party inspection

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Incoloy 800H pipes and tubes from mills that certify grain size and solution annealing. We provide EN 10204 3.1 certificates showing heat treatment and grain size, cut lengths on request, and export packing in wooden cases. Send us your specification for a fast quote.

Applications

Hydrogen and syngas plantsReformer outlet pigtails, manifolds and transfer lines.
Ethylene productionFurnace components and hot process piping.
PetrochemicalHigh-temperature heat exchangers and process heaters.
Power generationSuperheater and reheater tubing in high-temperature units.
Heat treatmentFurnace rolls, radiant tubes and retorts under load at high temperature.
Nitric acid plantsTail gas heaters and hot process lines.

Frequently asked questions

Why is grain size specified for Incoloy 800H?

A coarse grain size of ASTM No. 5 or coarser improves creep and stress rupture strength at high temperature.

What is the carbon range of Incoloy 800H?

Carbon is controlled to 0.05 – 0.10%, compared with 0.10% max for Incoloy 800.

Can Incoloy 800H be certified as 800 as well?

Yes. Material meeting the 800H limits often also meets Incoloy 800, and mills commonly dual-certify it on request.

Above what temperature is 800H preferred to 800?

Incoloy 800H is generally used where creep governs design, typically above about 600 °C.