Request Quote
  1. Home
  2. Products
  3. Inconel
  4. Incoloy 800HT Pipes & Tubes

Incoloy 800HT Pipes & Tubes

Incoloy 800HT (UNS N08811) pipes and tubes to ASTM B407 with Al+Ti 0.85 to 1.20% for maximum creep strength in reformers and crackers, from Riyaarth Overseas.

Incoloy 800HT Pipes & Tubes by Riyaarth Overseas

Incoloy 800HT pipes and tubes are made from UNS N08811 (Werkstoff 1.4959), the most tightly controlled member of the Incoloy 800 family. Carbon is held at 0.06 – 0.10%, the combined aluminium and titanium content is kept between 0.85 and 1.20%, and the material is solution annealed at 1149 °C (2100 °F) minimum to a grain size of ASTM No. 5 or coarser. These limits give the highest creep and rupture strength of the three grades.

Incoloy 800HT is specified for the hottest parts of hydrogen reformers, ethylene crackers and high-temperature heat exchangers, where long creep life matters. Material that meets 800HT also falls within the 800H and 800 limits, so it is often triple certified. Riyaarth Overseas supplies and exports Incoloy 800HT seamless and welded pipes and tubes with full certification.

Key Features

Highest creep strength: Tighter carbon, aluminium and titanium control gives better creep and stress rupture properties than 800H.

Higher annealing temperature: Solution annealing at 1149 °C min develops the coarse grain structure needed for long-term high-temperature service.

Oxidation resistance: The alloy resists oxidation and carburisation in hot process gases.

Multiple certification: 800HT material normally also meets 800 and 800H, which simplifies stock holding for plant operators.

Specifications

ParameterDetails
StandardsASTM B407 / ASME SB407 (seamless pipe and tube), B163 / SB163 (heat exchanger tube), B514 (welded pipe), B515 (welded tube)
Grade / UNSIncoloy 800HT / UNS N08811
Outside diameter rangeSmall-bore tube to NPS pipe sizes, as per enquiry
Wall thickness / scheduleSCH 5S, 10S, 40S, 80S, 160 or tube gauge
LengthRandom, fixed and cut lengths; U-bent tubes on request
TypeSeamless, welded
ConditionSolution annealed at 1149 °C (2100 °F) min, grain size ASTM No. 5 or coarser
EndsPlain end, bevelled end
Form / finishRound pipe and tube, pickled or bright annealed
Test certificateEN 10204 3.1 or 3.2

When ordering, state that the material must meet UNS N08811, and ask for the certificate to show carbon, aluminium, titanium, the combined aluminium plus titanium, the annealing temperature and the grain size. If dual or triple certification is needed for plant stock, mention it in the enquiry so the mill can confirm it.

Welding of 800HT uses filler metals intended for high-temperature service, and procedures are qualified for the operating range. Tube for reformer outlet systems is often ordered with extra ultrasonic or eddy current testing and with PMI on every length, as these parts are among the most critical in the plant.

Chemical Composition

ElementComposition (%)
Nickel (Ni)30.0 – 35.0
Chromium (Cr)19.0 – 23.0
Iron (Fe)39.5 min
Carbon (C)0.06 – 0.10
Manganese (Mn)1.50 max
Silicon (Si)1.00 max
Sulphur (S)0.015 max
Copper (Cu)0.75 max
Aluminium (Al)0.15 – 0.60
Titanium (Ti)0.15 – 0.60
Aluminium + Titanium0.85 – 1.20

Mechanical Properties

Property (ASTM B407)Value
Tensile strength, min450 MPa (65 ksi)
Yield strength (0.2%), min170 MPa (25 ksi)
Elongation, min30%
Density7.94 g/cm³
Melting range1357 – 1385 °C

Equivalent Grades

Standard / systemDesignation
UNSN08811
Werkstoff Nr.1.4959
ENX8NiCrAlTi32-21
Common namesAlloy 800HT

Testing and Inspection

Incoloy 800HT orders are tested to ASTM B407 or B163, with checks on the controlled chemistry and grain structure.

  • Chemical analysis confirming carbon and aluminium plus titanium
  • Grain size measurement (ASTM No. 5 or coarser)
  • Tensile testing and flattening or flaring tests
  • Hydrostatic test or eddy current test on every length
  • Positive material identification (PMI)
  • Third-party inspection on request

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Incoloy 800HT pipes and tubes from mills that certify chemistry, annealing temperature and grain size, with triple certification available on request. Every lot comes with EN 10204 3.1 documents, cut lengths can be arranged, and material is packed in wooden cases for export. We respond quickly to project enquiries.

Applications

Steam methane reformersOutlet pigtails, collectors and manifolds at the highest metal temperatures.
Ethylene crackersCrossover piping, outlet headers and furnace hardware.
Hydrogen productionHot transfer lines and heat exchangers in hydrogen plants.
Industrial furnacesLoad-bearing radiant tubes, rolls and fixtures.
Heat recoveryHigh-temperature recuperators and exchanger tubes.
Chemical processingProcess heater coils and lines in high-temperature units.

Frequently asked questions

What makes Incoloy 800HT different from 800H?

800HT has a narrower carbon range (0.06 – 0.10%), aluminium plus titanium of 0.85 – 1.20% and a higher minimum annealing temperature, giving better creep strength.

Can 800HT be used in place of 800H?

Yes. 800HT normally meets all 800H requirements and is often supplied triple certified as 800, 800H and 800HT.

Which standard covers Incoloy 800HT seamless pipe?

ASTM B407 covers seamless pipe and tube, and ASTM B163 covers heat exchanger tubes.

Where is Incoloy 800HT used most?

It is used mainly in hydrogen reformer outlet systems, ethylene cracker piping and other high-temperature process equipment.