Request Quote
  1. Home
  2. Products
  3. Inconel
  4. Inconel 601 Pipes & Tubes

Inconel 601 Pipes & Tubes

Inconel 601 (UNS N06601) pipes and tubes to ASTM B167 for oxidation resistance in furnaces, heat treatment and thermal processing, from Riyaarth Overseas.

Inconel 601 Pipes & Tubes by Riyaarth Overseas

Inconel 601 pipes and tubes are made from a nickel-chromium-iron alloy, UNS N06601 (Werkstoff 2.4851), with an addition of aluminium. The aluminium and high chromium form a tight, adherent oxide layer that resists spalling even under severe thermal cycling, which is the main reason the alloy is chosen. Seamless pipe and tube are produced to ASTM B167, and heat exchanger tubes to ASTM B163.

Inconel 601 is a standard material for heat treating equipment, furnace parts and thermal processing where metal temperatures are very high and oxidation, carburisation and sulphur-bearing atmospheres must be resisted. Riyaarth Overseas supplies and exports Inconel 601 pipes and tubes, cut to length, with full traceability documents.

Key Features

Cyclic oxidation resistance: Aluminium in the 1.0 – 1.7% range helps form a protective oxide that stays in place through repeated heating and cooling.

High-temperature strength: The alloy keeps useful mechanical strength at temperatures where stainless steels lose it.

Resistance to carburisation: High nickel and chromium give good resistance to carburising atmospheres in heat treatment furnaces.

Metallurgical stability: Inconel 601 keeps its ductility after long exposure at high temperature.

Specifications

ParameterDetails
StandardsASTM B167 / ASME SB167 (seamless pipe and tube), ASTM B163 / SB163 (heat exchanger tube)
Grade / UNSInconel 601 / UNS N06601
Outside diameter rangeSmall-bore tube to NPS pipe sizes, as per enquiry
Wall thickness / scheduleSCH 5S to SCH 160 or tube gauge
LengthRandom, fixed and cut lengths
TypeSeamless, hot-worked or cold-worked
ConditionAnnealed
EndsPlain end, bevelled end
Form / finishRound pipe and tube, pickled or bright annealed
Test certificateEN 10204 3.1 or 3.2

Inconel 601 is normally specified where oxidation resistance at very high temperature governs the choice, rather than aqueous corrosion. For wet corrosive service at lower temperature, alloys such as Inconel 625 or Incoloy 825 are usually a better fit, while 601 is used for parts that run hot in air or in combustion gases.

Furnace builders often use 601 tube for radiant tubes and muffles because the oxide layer stays attached through heating and cooling cycles, which reduces scaling losses and contamination of the work load. For thermocouple protection, the tube is ordered in small diameters with one end closed by the fabricator.

When ordering, give the outside diameter, wall thickness, length and the operating temperature and atmosphere, so that the condition and finish can be confirmed with the mill.

Chemical Composition

ElementComposition (%)
Nickel (Ni)58.0 – 63.0
Chromium (Cr)21.0 – 25.0
Iron (Fe)Balance
Aluminium (Al)1.0 – 1.7
Carbon (C)0.10 max
Manganese (Mn)1.0 max
Silicon (Si)0.50 max
Sulphur (S)0.015 max
Copper (Cu)1.0 max

Mechanical Properties

Property (ASTM B167)Value
Tensile strength, min (cold-worked or hot-worked annealed)550 MPa (80 ksi)
Yield strength (0.2%), min, cold-worked annealed205 MPa (30 ksi)
Yield strength (0.2%), min, hot-worked annealed170 MPa (25 ksi)
Elongation, min30% (cold-worked), 35% (hot-worked)
Density8.11 g/cm³
Melting range1360 – 1411 °C

Equivalent Grades

Standard / systemDesignation
UNSN06601
Werkstoff Nr.2.4851
EN / DINNiCr23Fe
Common namesAlloy 601, Nicrofer 6023

Testing and Inspection

Inconel 601 pipes and tubes are tested to ASTM B167 or B163 and the purchase order.

  • Chemical analysis including aluminium content
  • Tensile, flattening and flaring tests
  • Hydrostatic test or eddy current test on every length
  • Positive material identification (PMI)
  • Dimensional and visual inspection
  • Third-party inspection on request

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Inconel 601 pipes and tubes from reliable mills and stockists, cut to the lengths your furnace or plant needs. We provide EN 10204 3.1 certificates with every lot and pack in wooden cases for export. Send your sizes for a quick quotation.

Applications

Heat treatmentRadiant tubes, retorts, muffles and baskets in carburising and annealing furnaces.
Industrial furnacesBurner tubes, flame shields and thermocouple protection tubes.
PetrochemicalCatalyst support grids and reformer components exposed to high temperature.
Power generationCombustion chamber parts and superheater tube supports.
Pollution controlThermal reactors and incinerator parts in hot oxidising gases.
Glass and ceramicsHot zone tubing and fixtures in kilns and glass processing.

Frequently asked questions

What is Inconel 601 used for?

It is used mainly in furnaces, heat treatment equipment and thermal processing where high-temperature oxidation resistance is needed.

How is Inconel 601 different from Inconel 600?

Inconel 601 has more chromium and adds aluminium, which improves oxidation resistance, especially under thermal cycling.

Which ASTM standard covers Inconel 601 pipe?

ASTM B167 covers Inconel 601 seamless pipe and tube; ASTM B163 covers condenser and heat exchanger tubes.

Is Inconel 601 weldable?

Yes. It can be welded by common arc processes using matching nickel alloy filler metal.