Request Quote
  1. Home
  2. Products
  3. Monel
  4. Monel K500 Pipes & Tubes

Monel K500 Pipes & Tubes

Monel K500 (UNS N05500) age-hardenable nickel-copper tubes and pipes for marine, oil field and pump service, supplied and exported by Riyaarth Overseas.

Monel K500 Pipes & Tubes by Riyaarth Overseas

Monel K500 is a precipitation-hardenable nickel-copper alloy, UNS N05500 and Werkstoff 2.4375. It has the corrosion resistance of Monel 400, but additions of aluminium and titanium allow it to be age hardened, which raises its strength and hardness well above that of Monel 400. It is non-magnetic down to low temperatures and is used where a strong, corrosion-resistant part must work in seawater or sour environments.

There is no dedicated ASTM pipe standard for this grade, so K500 tubes are produced to mill or purchaser specifications, with chemistry to UNS N05500 as used in ASTM B865 and AMS 4676 for bar products. Tubes are generally supplied annealed for forming and then age hardened by the user, or supplied in the aged condition when ordered. Riyaarth Overseas supplies and exports Monel K500 tubes and hollow sections with full documentation.

Age hardening is normally carried out at about 590 to 610 °C for several hours, followed by slow cooling in the furnace through a lower temperature range, which develops the full strength of the alloy. Parts should be machined roughly before ageing and finished afterwards, since the alloy is much harder in the aged condition. When enquiring, please state the required condition, any hardness or NACE limits, the size and the length, so that the mill certificate can confirm compliance.

Key Features

Age-hardenable strength: Aluminium and titanium form fine precipitates during ageing, giving Monel K500 roughly two to three times the yield strength of annealed Monel 400.

Seawater corrosion resistance: The base nickel-copper chemistry gives the same low corrosion rates in flowing seawater as Monel 400, so strength is gained without losing marine performance.

Low magnetic permeability: The alloy remains non-magnetic to well below room temperature, which suits instrument housings and oil field survey tools.

Sour service capability: K500 is used in hydrogen sulphide containing oil and gas environments within the hardness limits set by NACE MR0175 / ISO 15156.

Specifications

ParameterDetails
StandardsMill or purchaser specification; chemistry to UNS N05500 (ASTM B865 / AMS 4676 for bar); NACE MR0175 / ISO 15156 on request
Grade / UNSMonel K500, UNS N05500, W.Nr. 2.4375
Outside diameter rangeSeamless tube and hollow bar to order; sizes on enquiry
Wall thickness / scheduleAs per drawing or order, in mm or inch
LengthRandom and cut lengths
TypeSeamless (cold drawn or hot finished)
EndsPlain ends, bevelled or machined ends on request
Form / finishAnnealed, or annealed and age hardened; pickled or bright
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Nickel (Ni, incl. Co)63.0 min
Copper (Cu)27.0 – 33.0
Aluminium (Al)2.30 – 3.15
Titanium (Ti)0.35 – 0.85
Iron (Fe)2.0 max
Manganese (Mn)1.5 max
Carbon (C)0.25 max
Silicon (Si)0.5 max
Sulphur (S)0.01 max

Mechanical Properties

PropertyValue
Tensile strength (cold drawn, annealed tube, typical)90 – 110 ksi (621 – 758 MPa)
Yield strength, 0.2% offset (cold drawn, annealed tube, typical)40 – 65 ksi (276 – 448 MPa)
Elongation (cold drawn, annealed tube, typical)45 – 25%
Density8.44 g/cm³

These are typical ranges for annealed seamless tube, not specification minimums. Age hardening raises tensile and yield strength substantially; aged properties are agreed at the time of order and reported on the mill certificate.

Equivalent Grades

StandardDesignation
UNSN05500
Werkstoff Nr.2.4375
EN / DINNiCu30Al
Common namesMonel K500, Alloy K-500

Testing and Inspection

Monel K500 tubes are inspected according to the order specification and the heat treatment condition. Typical checks include:

  • Hardness testing: Confirms annealed or aged condition and NACE hardness limits where specified.
  • Tensile testing: Tensile, yield and elongation reported on the mill certificate.
  • Ultrasonic testing: Checks for internal defects in tube and hollow bar.
  • Positive material identification (PMI): Confirms nickel, copper, aluminium and titanium.
  • Dimensional and visual inspection: OD, ID, wall and length to the order.
  • Third-party inspection: Witness inspection by your appointed agency on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources Monel K500 tube from established nickel alloy mills and can supply it annealed for your own forming and ageing, or in the aged condition. We cut to length and supply EN 10204 3.1 certificates showing chemistry, heat treatment and mechanical results.

Material is packed for export in wooden boxes, and our team responds quickly with offers against your drawings or specifications.

Applications

Oil and gas drillingDrill collars, survey tool housings and downhole instrument tubing where non-magnetic strength is required.
Marine propulsionPump shafts, propeller shafts and impeller sleeves exposed to seawater.
Valves and pumpsValve trim, stems and pump components for seawater and sour service.
Offshore structuresFasteners, sleeves and hollow components on platforms and subsea equipment.
Chemical processingSprings, bellows and wear parts in equipment that already uses Monel 400 piping.
Defence and navalHull fittings and sonar and instrument parts requiring low magnetic permeability.

Frequently asked questions

What is the difference between Monel 400 and Monel K500?

Both are nickel-copper alloys with similar corrosion resistance, but K500 contains aluminium and titanium, which allow it to be age hardened to much higher strength and hardness.

Is there an ASTM pipe specification for Monel K500?

No dedicated ASTM pipe specification exists for UNS N05500. Tubes are produced to mill or purchaser specifications, with chemistry and properties agreed with reference to ASTM B865 and AMS 4676.

Is Monel K500 magnetic?

Monel K500 has very low magnetic permeability and stays non-magnetic to about minus 100 °C, which is why it is used for oil field survey tools.

Should I order K500 tubes annealed or aged?

Order annealed tube if you will bend, machine heavily or weld before final heat treatment, then age harden the finished part. Order aged tube when the part will be used after simple machining.