Request Quote
  1. Home
  2. Products
  3. Titanium
  4. Titanium Grade 2 Pipes & Tubes

Titanium Grade 2 Pipes & Tubes

Titanium Grade 2 (UNS R50400) seamless and welded pipes and tubes to ASTM B338, B861 and B862, stocked and exported by Riyaarth Overseas, Mumbai, India.

Titanium Grade 2 Pipes & Tubes by Riyaarth Overseas

Titanium Grade 2 is commercially pure titanium, UNS R50400 and Werkstoff 3.7035. It is the most widely used titanium grade for pipe and tube because it offers a good balance of strength, ductility, weldability and corrosion resistance. A stable, self-healing oxide film protects it in seawater, chloride solutions, wet chlorine, hypochlorite and many oxidising acids.

Grade 2 tubes for condensers and heat exchangers are made to ASTM B338 / ASME SB338 in seamless or welded form, seamless pipe to ASTM B861 and welded pipe to ASTM B862. At about 4.51 g/cm³ it weighs roughly 57 percent as much as steel, which reduces structural load in offshore and process equipment.

Riyaarth Overseas supplies and exports Titanium Grade 2 pipes and tubes to power, desalination, chemical and offshore projects, in straight lengths, U-bends and cut lengths with full mill certification.

Titanium Grade 2 should not be used in dry chlorine gas, fuming nitric acid or strongly reducing acids such as concentrated hydrochloric acid, where the oxide film cannot be maintained. In those duties a palladium-bearing grade such as Grade 7 or a nickel alloy is normally selected. When enquiring, please give the specification, OD, wall thickness, length and whether tubes are needed straight or U-bent.

Key Features

Seawater and chloride resistance: Grade 2 is practically immune to general corrosion, pitting and crevice corrosion in seawater at normal temperatures, which is why it is widely used for seawater-cooled condensers.

Low density: With a density of 4.51 g/cm³, Grade 2 gives a lighter piping system than steel or nickel alloys of the same size, an advantage on offshore platforms and ships.

Good formability and weldability: Commercially pure titanium bends, flares and expands into tube sheets readily and is welded by TIG with proper inert gas shielding of both sides of the joint.

Erosion resistance: The oxide film resists high-velocity seawater and entrained sand better than copper alloys, so higher flow velocities can be used in tube bundles.

Specifications

ParameterDetails
StandardsASTM B338 / ASME SB338 (tubes), ASTM B861 / ASME SB861 (seamless pipe), ASTM B862 / ASME SB862 (welded pipe)
Grade / UNSTitanium Grade 2, UNS R50400, W.Nr. 3.7035
Outside diameter rangeTube from 6.35 mm (1/4 in) OD; pipe NPS 1/4 in to 8 in, larger sizes in welded form
Wall thickness / scheduleSCH 5S, 10S, 40S, 80S; tube wall in BWG or mm
LengthRandom, fixed and cut lengths
TypeSeamless, welded
EndsPlain ends, bevelled ends, threaded ends on request
Form / finishRound, U-bent, coiled; annealed, pickled
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Nitrogen (N)0.03 max
Carbon (C)0.08 max
Hydrogen (H)0.015 max
Iron (Fe)0.30 max
Oxygen (O)0.25 max
Residual elements, each0.1 max
Residual elements, total0.4 max
Titanium (Ti)Balance

Mechanical Properties

PropertyValue
Tensile strength50 ksi (345 MPa) min
Yield strength, 0.2% offset40 – 65 ksi (275 – 450 MPa)
Elongation in 2 in (50 mm)20% min
Density4.51 g/cm³

Equivalent Grades

StandardDesignation
UNSR50400
Werkstoff Nr.3.7035
JISClass 2
Common namesCP titanium Grade 2, Ti Gr 2

Testing and Inspection

Titanium Grade 2 pipes and tubes are tested to ASTM B338, B861 or B862 as ordered. Typical inspection includes:

  • Hydrostatic or pneumatic test: Pressure testing of each length.
  • Eddy current or ultrasonic test: Non-destructive testing for wall defects.
  • Flattening and flaring tests: Ductility checks on samples from each lot.
  • Chemical analysis: Including interstitial elements oxygen, nitrogen, hydrogen and carbon.
  • Dimensional and visual inspection: OD, wall, length and surface condition.
  • Third-party inspection: Witness inspection by your nominated agency on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies Titanium Grade 2 pipes and tubes from stock and from established titanium mills, in full lengths, U-bends or cut lengths. Every delivery includes EN 10204 3.1 certificates with heat numbers and test results.

We pack titanium in wooden boxes with protective sleeves for export and send quotations promptly against your tube schedules or piping lists.

Applications

Power generationSeawater-cooled surface condenser tubes in coastal power stations.
DesalinationHeat exchanger and brine heater tubing in thermal desalination plants.
Chemical processingPiping and heat exchangers handling wet chlorine, chlorine dioxide, hypochlorite and nitric acid.
Offshore oil and gasSeawater lift, fire water and cooling water piping where weight saving matters.
Pulp and paperBleach plant piping and heat exchangers exposed to chlorine-based bleaches.
Marine engineeringShip cooling systems and seawater pipework with long service intervals.

Frequently asked questions

Which standard covers Titanium Grade 2 heat exchanger tubes?

Titanium Grade 2 condenser and heat exchanger tubes are made to ASTM B338 / ASME SB338, in seamless or welded form.

Is Titanium Grade 2 suitable for seawater?

Yes. Grade 2 is practically immune to seawater corrosion at normal temperatures, including pitting and crevice corrosion, and it resists erosion at high flow velocities.

What is the difference between Grade 1 and Grade 2 titanium?

Both are commercially pure. Grade 2 allows more oxygen and iron, which gives higher strength, while Grade 1 is softer and easier to form.

Can titanium pipe be welded on site?

Yes, by TIG welding, provided the weld and the hot metal on both sides are fully shielded with argon to prevent contamination by air.