Request Quote
  1. Home
  2. Products
  3. Super Duplex
  4. UNS S32906 Super Duplex Stainless Steel Pipes & Tubes

UNS S32906 Super Duplex Stainless Steel Pipes & Tubes

UNS S32906 (1.4477, SAF 2906) super duplex pipes and tubes to ASTM A789 and A790, 29% Cr, for urea, caustic and chloride service, from Riyaarth Overseas.

UNS S32906 Super Duplex Stainless Steel Pipes & Tubes by Riyaarth Overseas

UNS S32906 is a highly alloyed duplex stainless steel with about 29% chromium, 7% nickel, 2.3% molybdenum and 0.35% nitrogen. It is best known as SAF 2906 and is EN 1.4477. With a minimum pitting resistance equivalent above 40, it falls in the super duplex class, and its high chromium and nitrogen give very high strength and resistance to pitting, crevice corrosion and chloride stress corrosion cracking.

The grade was developed for urea production, where its resistance to carbamate solutions is used in strippers, condensers and high pressure piping, and it is also used in caustic soda and alumina plants. Tubes are made to ASTM A789 and pipes to ASTM A790. Riyaarth Overseas supplies and exports S32906 pipes and tubes from mill sources for plant and maintenance orders.

Key Features

Very high chromium: At 28.0 – 30.0% chromium, S32906 is one of the highest chromium duplex grades, which suits strongly oxidising environments.

Super duplex corrosion resistance: Its PRE of about 41 and above gives high resistance to pitting and crevice corrosion in chloride solutions.

Wall-dependent strength: ASTM A789 sets a higher strength requirement for walls below 10 mm (yield 650 MPa) than for heavier walls (yield 550 MPa).

Urea grade service: It is used in high pressure urea equipment where carbamate attack limits austenitic urea grades.

Specifications

ItemDetails
StandardsASTM A789 / ASME SA-789 (tubes), ASTM A790 / ASME SA-790 (pipes)
GradeUNS S32906 / EN 1.4477
Outside diameterTubes and pipes in sizes to the order, subject to mill availability
Wall thickness / scheduleTubes in average or minimum wall; pipes per ASME B36.19M / B36.10M schedules
LengthRandom lengths, fixed lengths and cut lengths
TypeSeamless
EndsPlain ends, bevelled ends
Form / finishSolution annealed (1020 – 1150 °C) and pickled
Test certificateEN 10204 3.1 standard; EN 10204 3.2 with third-party witness on request

Chemical Composition

ElementComposition (%)
Carbon (C)0.030 max
Manganese (Mn)0.80 – 1.50
Phosphorus (P)0.030 max
Sulphur (S)0.030 max
Silicon (Si)0.80 max
Nickel (Ni)5.8 – 7.5
Chromium (Cr)28.0 – 30.0
Molybdenum (Mo)1.50 – 2.60
Nitrogen (N)0.30 – 0.40
Copper (Cu)0.80 max

Mechanical Properties

PropertyWall below 10 mm (0.40 in.)Wall 10 mm (0.40 in.) and above
Tensile strength, min116 ksi (800 MPa)109 ksi (750 MPa)
Yield strength, min94 ksi (650 MPa)80 ksi (550 MPa)
Elongation in 2 in., min25%25%
Hardness, max300 HBW / 32 HRC300 HBW / 32 HRC
Density7.7 g/cm³7.7 g/cm³

Equivalent Grades

SystemDesignation
UNSS32906
EN / Werkstoff1.4477 (X2CrNiMoN29-7-2)
Trade namesSAF 2906; Safurex in urea service
JISNo direct equivalent

Testing and Inspection

Testing follows ASTM A789 or A790. Urea grade orders often carry extra end-user requirements that must be agreed at enquiry stage.

  • Hydrostatic or eddy current: Each length is hydrostatically tested or eddy current tested.
  • Flaring and flattening: Flaring on seamless tube and flattening on pipe per the specification.
  • Tensile and hardness: Tests per lot against the wall-dependent limits.
  • Corrosion and microstructure tests: Ferrite content, intermetallic phase checks or corrosion tests when specified by the licensor or end user.
  • PMI: Positive material identification on every length when ordered.
  • Third-party inspection: Witness inspection and EN 10204 3.2 certification on request.

When ordering, state whether tubes are for A789 or pipe for A790, the size and wall, the length and quantity, and any licensor specification that applies to urea service. Welding should use a qualified procedure with low to moderate heat input and a filler metal suited to this grade, and interpass temperature should be controlled so that intermetallic phases do not form in the weld or heat affected zone.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources S32906 pipes and tubes from mills that produce this grade, and confirms any licensor or end-user requirement before order. Material can be cut to length and is shipped with EN 10204 3.1 mill test certificates in export packing. Send your tube list for a quotation.

Applications

Urea productionUsed for stripper tubes, condenser tubes and high pressure piping exposed to ammonium carbamate.
Caustic soda plantsUsed for piping from the cells to the evaporation plant and for evaporator tubes.
Alumina refiningUsed for heat exchanger tubes and piping in the digestion stage.
Chemical processingProcess piping where high chloride content and oxidising conditions occur together.
Seawater systemsCoolers and piping where pitting and crevice corrosion resistance is the main requirement.
Oil and gasProcess piping and heat exchanger tubes handling chloride-bearing produced water.

Frequently asked questions

Is UNS S32906 duplex or super duplex?

It is a super duplex stainless steel. Its high chromium and nitrogen give a PRE above 40, which is the usual threshold for super duplex grades.

What is the EN number for UNS S32906?

The EN steel number is 1.4477.

Why is S32906 used in urea plants?

Its very high chromium content gives good resistance to ammonium carbamate solutions, so it is used in strippers, condensers and high pressure piping.

Why does strength depend on wall thickness?

Thinner walls receive more working and finer structure during manufacture, so ASTM A789 sets higher minimums for walls below 10 mm.