Request Quote
  1. Home
  2. Products
  3. Carbon Steel
  4. ASTM A179 / SA179 Tubes

ASTM A179 / SA179 Tubes

ASTM A179 / ASME SA179 seamless cold-drawn low carbon steel tubes for heat exchangers and condensers, 72 HRB max, supplied and exported by Riyaarth Overseas.

ASTM A179 / SA179 Tubes by Riyaarth Overseas

ASTM A179 covers seamless cold-drawn low carbon steel tubes for tubular heat exchangers, condensers and similar heat transfer equipment. ASME SA-179 is the identical code version used in boiler and pressure vessel work. The specification covers outside diameters from 1/8 in. to 3 in. (3.2 to 76.2 mm).

A179 tubes are made by the seamless process, cold drawn to size and heat treated after the final cold draw at 1200 °F (650 °C) or higher. The low carbon chemistry and a maximum hardness of 72 HRB make the tubes soft enough to be expanded and rolled into tubesheets without splitting, which is why A179 is one of the most widely used exchanger tube specifications.

Riyaarth Overseas supplies and exports ASTM A179 / SA179 tubes in straight lengths and U-bends from mill sources, for exchanger fabricators and plant maintenance teams.

Key Features

Made for tube expansion: The 72 HRB hardness limit and flaring and flange tests confirm the tube can be expanded into tubesheets.

Cold drawn accuracy: Cold drawing gives close tolerances on outside diameter and wall, which helps tube-to-tubesheet joints.

Good heat transfer: Plain carbon steel has good thermal conductivity, so A179 suits heat transfer service in non-corrosive media.

Economical choice: Where the process fluid allows carbon steel, A179 costs far less than stainless or copper alloy tubing.

Specifications

ItemDetails
StandardASTM A179 / ASME SA-179
MaterialLow carbon steel
Outside diameter1/8 in. to 3 in. (3.2 to 76.2 mm)
Wall thicknessMinimum or average wall as ordered (BWG gauges common)
LengthFixed lengths to exchanger drawings; U-bends on request
TypeSeamless, cold drawn
EndsPlain ends, deburred
Form / finishHeat treated after final cold draw at 650 °C (1200 °F) or higher; oiled or varnished
Test certificateEN 10204 3.1 standard; EN 10204 3.2 with third-party witness on request

Chemical Composition

ElementComposition (%)
Carbon (C)0.06 – 0.18
Manganese (Mn)0.27 – 0.63
Phosphorus (P)0.035 max
Sulphur (S)0.035 max

Mechanical Properties

PropertyValue
Tensile strength47 ksi (325 MPa) min
Yield strength26 ksi (180 MPa) min
Elongation in 2 in. (50 mm)35% min
Hardness72 HRB max

Equivalent Grades

Approximate equivalents for comparison only. Check limits before substitution.

StandardComparable grade
EN 10216-1P195TR1 / P195TR2
DIN 17175 (withdrawn)St 35.8
JIS G3461STB 340

Testing and Inspection

Testing follows ASTM A179 and the general requirements of ASTM A450.

  • Hydrostatic or electric test: Each tube is hydrostatically tested or passed through an eddy current or ultrasonic test.
  • Flattening test: One flattening test on each lot.
  • Flaring test: One flaring test on each lot to confirm expansion capability.
  • Flange test: Flange test as required by the specification.
  • Hardness test: Rockwell hardness checked against the 72 HRB limit.
  • Visual and dimensional: Outside diameter, wall, length and straightness checks, with third-party inspection on request.

When ordering A179 tubes, state the outside diameter, minimum or average wall, length, quantity and whether straight tubes or U-bends are needed. For U-bends, give the bend radii and leg lengths from the exchanger drawing, and state whether stress relief of the bent portion is required. The tube is intended for service where the shell and tube side fluids are compatible with plain carbon steel.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies ASTM A179 / SA179 tubes from ready stock and established mill sources, and can arrange cut lengths, bevelling and end protection to suit your project. Every shipment carries EN 10204 3.1 mill test certificates with full heat traceability, and material is bundled and marked for export. Send your size list for a fast quotation.

Applications

Shell and tube heat exchangersUsed for tube bundles in refineries, chemical plants and fertiliser units handling non-corrosive fluids.
Surface condensersUsed in steam condensers where cooling water quality allows carbon steel.
Air coolersUsed as the base tube in finned air-cooled exchangers.
Feedwater heatersUsed in low pressure feedwater heaters in power and process plants.
Oil coolersUsed in lube oil and hydraulic oil coolers on rotating equipment.
HVAC and refrigerationUsed in chillers and heat recovery units with closed-loop water.

Frequently asked questions

What is ASTM A179 tube used for?

It is used for tubular heat exchangers, condensers and similar heat transfer equipment.

Is ASTM A179 the same as ASME SA179?

Yes. ASME SA-179 adopts ASTM A179, and tubes are usually dual-marked A179/SA179.

What is the size range of A179 tubes?

The specification covers outside diameters from 1/8 in. to 3 in. (3.2 to 76.2 mm).

Why is A179 tube heat treated after cold drawing?

Cold drawing hardens the steel. Heat treatment at 650 °C or higher softens it so the tube meets the 72 HRB limit and can be expanded into tubesheets.