
ASTM A192 / SA192 Tubes
ASTM A192 / ASME SA192 seamless carbon steel boiler tubes for high pressure service, 1/2 in. to 7 in. OD, supplied and exported by Riyaarth Overseas, Mumbai.

ASTM A192 covers seamless carbon steel boiler and superheater tubes for high pressure service. ASME SA-192 is the code version used in boiler construction. The specification covers tubes from 1/2 in. to 7 in. (12.7 to 177.8 mm) outside diameter, with minimum wall thicknesses from 0.085 in. to 1.000 in. (2.2 to 25.4 mm).
A192 tubes are made seamless, either hot finished or cold drawn. Hot finished tubes need no further heat treatment, while cold drawn tubes are heat treated after the final cold draw at 1200 °F (650 °C) or higher. The chemistry is close to A179, with an added silicon limit, and the tubes are ordered by minimum wall thickness, which suits boiler pressure calculations.
Riyaarth Overseas supplies and exports ASTM A192 / SA192 boiler tubes from mill sources for boiler manufacturers, power plants and process industries.
Key Features
High pressure boiler service: The specification is written for boiler and superheater tubes in high pressure steam generation.
Ordered by minimum wall: Tubes are supplied to minimum wall thickness, so the full design wall is guaranteed at every point.
Hot finished or cold drawn: Large sizes are usually hot finished, while smaller and thinner tubes are cold drawn for close tolerances.
Good formability: Low carbon and a hardness limit of 77 HRB allow bending, swaging and expanding during boiler fabrication.
Specifications
| Item | Details |
|---|---|
| Standard | ASTM A192 / ASME SA-192 |
| Material | Carbon steel |
| Outside diameter | 1/2 in. to 7 in. (12.7 to 177.8 mm) |
| Wall thickness | 0.085 in. to 1.000 in. (2.2 to 25.4 mm) minimum wall |
| Length | Fixed and random lengths; bends on request |
| Type | Seamless, hot finished or cold drawn |
| Ends | Plain ends, bevelled ends |
| Form / finish | Hot finished, or heat treated at 650 °C (1200 °F) or higher after cold drawing; varnished or oiled |
| Test certificate | EN 10204 3.1 standard; EN 10204 3.2 with third-party witness on request |
Chemical Composition
| Element | Composition (%) |
|---|---|
| Carbon (C) | 0.06 – 0.18 |
| Manganese (Mn) | 0.27 – 0.63 |
| Phosphorus (P) | 0.035 max |
| Sulphur (S) | 0.035 max |
| Silicon (Si) | 0.25 max |
Mechanical Properties
| Property | Value |
|---|---|
| Tensile strength | 47 ksi (325 MPa) min |
| Yield strength | 26 ksi (180 MPa) min |
| Elongation in 2 in. (50 mm) | 35% min |
| Hardness | 77 HRB max |
Equivalent Grades
Approximate equivalents for comparison only. Check limits before substitution.
| Standard | Comparable grade |
|---|---|
| EN 10216-2 | P195GH |
| DIN 17175 (withdrawn) | St 35.8 |
| JIS G3461 | STB 340 |
Testing and Inspection
Testing follows ASTM A192 and the general requirements of ASTM A450.
- Hydrostatic or electric test: Each tube is hydrostatically tested or passed through a non-destructive electric test.
- Flattening test: Flattening test on each lot.
- Flaring test: Flaring test on each lot.
- Hardness test: Rockwell hardness checked against the 77 HRB limit.
- Tensile test: Tensile and yield strength checked per lot.
- Third-party inspection: Witness inspection, including IBR inspection for Indian boiler projects when ordered.
When ordering A192 tubes, state the outside diameter, minimum wall thickness, length and quantity, and whether hot finished or cold drawn tubes are acceptable. For Indian boiler projects, state if IBR inspection is required so that it can be arranged at the mill. Design temperature limits for carbon steel tubes are set by the applicable boiler code, and superheater sections above those limits need alloy steel tubes such as A213 T11 or T22.
Why Choose Riyaarth Overseas
Riyaarth Overseas supplies ASTM A192 / SA192 boiler tubes from ready stock and established mill sources, and can arrange cut lengths, bevelling and end protection to suit your project. Every shipment carries EN 10204 3.1 mill test certificates with full heat traceability, and material is bundled and marked for export. Send your size list for a fast quotation.
Applications






Frequently asked questions
What is ASTM A192 used for?
It is used for boiler and superheater tubes in high pressure service, and for economisers and heat recovery steam generators.
What is the difference between A179 and A192?
A179 is a cold drawn exchanger tube ordered for heat exchangers and condensers. A192 is a boiler tube for high pressure service, ordered by minimum wall, with a size range up to 7 in. OD and a hardness limit of 77 HRB.
Is A192 the same as SA192?
Yes. ASME SA-192 adopts ASTM A192 for boiler code work.
Can A192 tubes be supplied with IBR certification?
Yes. Tubes for Indian boiler projects can be supplied with IBR inspection and documentation when ordered.
