Request Quote
  1. Home
  2. Products
  3. Carbon Steel
  4. ASTM A513 DOM Tubing

ASTM A513 DOM Tubing

ASTM A513 Type 5 DOM (drawn over mandrel) carbon steel tubing in grades 1020 and 1026, for hydraulic cylinders and machined parts, from Riyaarth Overseas.

ASTM A513 DOM Tubing by Riyaarth Overseas

ASTM A513 covers electric resistance welded carbon and alloy steel mechanical tubing. DOM (drawn over mandrel) tubing is Type 5 in the specification: an ERW tube that is cold drawn over a mandrel and through a die after welding. Cold drawing works the weld zone and the body together, so the seam becomes practically undetectable and the tube gains close tolerances, a smooth surface and higher strength.

DOM tubing is a mechanical tube, not a pressure pipe. It is ordered by outside diameter and wall thickness or by outside and inside diameter, and is used where concentricity, machinability and strength matter, such as hydraulic cylinders, shafts, bushings and automotive parts. Grades 1020 and 1026 are the most common.

Riyaarth Overseas supplies and exports ASTM A513 Type 5 DOM tubing from mill sources, in random lengths and cut pieces, for engineering and fabrication customers.

Key Features

Close tolerances: Drawing over a mandrel gives tight control of outside diameter, inside diameter and wall, which reduces machining.

Uniform weld zone: Cold working after welding makes the seam area uniform with the body of the tube.

Higher strength than as-welded tube: Cold drawing raises yield and tensile strength compared with as-welded Type 1 or Type 2 tubing.

Good machinability: Concentric walls and a consistent structure suit turning, honing and boring.

Specifications

ItemDetails
StandardASTM A513 Type 5 (DOM)
Grades1020, 1026; other grades in the specification on request
Outside diameterSmall to large mechanical tube sizes, to the order
Wall thicknessOrdered by OD and wall, or by OD and ID
LengthRandom lengths and cut lengths
TypeElectric resistance welded, drawn over mandrel
EndsSquare cut ends
Form / finishAs drawn or stress relieved; oiled
Test certificateEN 10204 3.1

Chemical Composition

Composition for grade 1026, the grade most used for DOM hydraulic tube.

ElementComposition (%)
Carbon (C)0.22 – 0.28
Manganese (Mn)0.60 – 0.90
Phosphorus (P)0.035 max
Sulphur (S)0.035 max

Mechanical Properties

Minimum values for Type 5 DOM tubing in the as-drawn condition.

PropertyGrade 1020Grade 1026
Yield strength, min60 ksi (414 MPa)70 ksi (483 MPa)
Tensile strength, min70 ksi (483 MPa)80 ksi (552 MPa)
Elongation in 2 in., min5%5%
Hardness80 HRB85 HRB

Equivalent Grades

DOM is a manufacturing route rather than a grade, so there is no single foreign equivalent. Grades 1020 and 1026 follow the SAE / AISI carbon steel numbering. For European orders, welded and cold drawn precision tubes to EN 10305-2 in grades such as E235 or E355 are the closest alternative.

Testing and Inspection

DOM tubing is tested to ASTM A513 and the order requirements.

  • Weld seam NDT: Non-destructive electric testing of the tube.
  • Flattening and flare tests: Flattening and flaring or flange tests to check weld ductility.
  • Tensile and hardness: Tensile and Rockwell hardness tests when ordered.
  • Dimensional checks: Outside diameter, inside diameter, wall, ovality and straightness checks.
  • Surface inspection: Visual check of inside and outside surface finish.
  • Third-party inspection: Witness inspection by a nominated agency on request.

When ordering DOM tubing, state the grade, outside diameter and wall (or outside and inside diameter), length and quantity, and whether the tube is to be supplied as drawn or stress relieved. For hydraulic cylinder barrels, state the honing or skiving allowance needed so that the right size can be selected. Stress relieved tube is easier to machine and straighten, while as-drawn tube has the higher strength values listed above.

Why Choose Riyaarth Overseas

Riyaarth Overseas supplies ASTM A513 DOM tubing from established mechanical tube mills and can arrange cut pieces to your drawing lengths. Each order carries EN 10204 3.1 mill test certificates, and tubes are oiled, capped and bundled for export. Send your OD, ID and length requirements for a quotation.

Applications

Hydraulic cylindersUsed for cylinder barrels that are honed or skived and roller burnished.
Automotive partsUsed for axle tubes, steering columns, drive shafts and suspension parts.
Machined componentsUsed for bushings, sleeves, spacers and rollers turned from tube.
Agricultural machineryUsed for shafts, pivots and cylinder bodies on tractors and implements.
Material handlingUsed for conveyor rollers, forklift parts and lifting equipment.
Motorsport and framesUsed for roll cages and chassis members where uniform walls and strength are needed.

Frequently asked questions

What does DOM mean?

DOM stands for drawn over mandrel. It is an ERW tube that is cold drawn over a mandrel and through a die after welding.

Is DOM tubing seamless?

No. DOM tubing starts as a welded tube, but cold drawing makes the seam area uniform with the body, so it is often used where seamless mechanical tube would otherwise be specified.

Which A513 type is DOM?

DOM is Type 5 in ASTM A513.

Can DOM tubing be used as pressure pipe?

ASTM A513 is a mechanical tubing specification, not a pressure piping specification, so it is not intended for code pressure piping.