Request Quote
  1. Home
  2. Products
  3. Carbon Steel
  4. DIN 2391 St35 Pipes & Tubes

DIN 2391 St35 Pipes & Tubes

DIN 2391 St35 cold drawn seamless precision steel tubes in BK, BKW, BKS, GBK and NBK conditions, supplied and exported by Riyaarth Overseas, Mumbai.

DIN 2391 St35 Pipes & Tubes by Riyaarth Overseas

DIN 2391 St35 tubes are cold drawn seamless precision steel tubes made to close tolerances on outside diameter and wall thickness. DIN 2391 Part 1 sets the dimensions and permissible variations, and Part 2 sets the technical delivery conditions, including the steel grades and the five delivery conditions: BK, BKW, BKS, GBK and NBK. St35 (material number 1.0308) is a low carbon, unalloyed steel that cold forms, bends and welds well, which is why it is the most widely used grade in the standard.

Buyers choose DIN 2391 St35 when a tube must slide into a fitting, carry hydraulic pressure or be machined with very little stock removal. The clean bright surface and tight tolerances cut down on finishing work. The standard has since been replaced by EN 10305-1 (grade E235), but many drawings, hydraulic systems and replacement parts still call for DIN 2391 St35. Riyaarth Overseas supplies and exports DIN 2391 St35 precision tubes from established mill sources, in random or cut lengths, with mill test certificates.

Key Features

Close dimensional tolerances: Cold drawing over a mandrel gives tight outside diameter and wall tolerances and good concentricity, so tubes fit compression fittings and bores without extra machining.

Choice of delivery condition: The same grade can be ordered hard drawn (BK), lightly drawn (BKW), drawn and stress relieved (BKS), annealed (GBK) or normalised (NBK), matching strength or ductility to the job.

Bright, clean surface: The inside and outside surfaces are smooth and free of scale, which suits hydraulic and lubrication lines where cleanliness of the bore matters.

Easy to form and weld: The low carbon content lets St35 tubes be bent, flared, expanded and welded readily, particularly in the GBK and NBK conditions.

Specifications

SpecificationDetails
StandardDIN 2391-1 (dimensions), DIN 2391-2 (technical delivery conditions)
GradeSt35 (material no. 1.0308)
Outside diameter rangeFrom 4 mm, sizes as per the DIN 2391-1 dimension table
Wall thicknessAs per DIN 2391-1 dimension table for each outside diameter
LengthRandom lengths, fixed lengths and cut-to-size pieces
TypeSeamless, cold drawn precision tube
Delivery conditionBK, BKW, BKS, GBK, NBK
EndsPlain ends, square cut, deburred
Form / finishRound; bright surface, oiled for protection
Test certificateEN 10204 3.1; 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Carbon (C)0.17 max
Silicon (Si)0.35 max
Manganese (Mn)0.40 min
Phosphorus (P)0.025 max
Sulphur (S)0.025 max

Mechanical Properties

PropertyValue
BK (hard drawn)Tensile 480 MPa min, elongation 6% min
BKW (lightly drawn)Tensile 420 MPa min, elongation 10% min
BKS (drawn and stress relieved)Tensile 420 MPa min, yield 315 MPa min, elongation 14% min
GBK (annealed)Tensile 315 MPa min, elongation 25% min
NBK (normalised)Tensile 340 – 470 MPa, yield 235 MPa min, elongation 25% min
Density7.85 g/cm³

Room temperature values as listed in DIN 2391-2. For BK, BKW and GBK tubes the standard gives tensile strength and elongation only; yield strength is not specified.

Equivalent Grades

SystemEquivalent
EN 10305-1 (current European standard)E235
Material number1.0308
Older DIN nameSt 35

Testing and Inspection

Each lot is tested to DIN 2391-2 and the purchase order. Typical checks are:

  • Chemical analysis: ladle analysis to confirm C, Si, Mn, P and S limits.
  • Tensile test: tensile strength, yield strength (where specified) and elongation for the ordered delivery condition.
  • Flattening and flaring or expanding tests: to confirm ductility, where ordered.
  • Leak tightness: hydrostatic test or eddy current test, as agreed.
  • Dimensional and visual checks: outside diameter, wall, straightness and surface condition.
  • Third-party inspection: available on request, with EN 10204 3.2 certification.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources DIN 2391 St35 tubes from established precision tube mills and holds commonly used sizes, so many enquiries can be served from stock. Tubes can be supplied in cut lengths, with EN 10204 3.1 mill test certificates and export packing in bundles with end caps. Send your sizes, delivery condition and quantity for a prompt quote.

Applications

Hydraulic systemsUsed for high pressure hydraulic lines and connecting tubes, usually in NBK condition, together with 24° cone compression fittings.
AutomotiveMade into fuel lines, brake and steering system parts, shafts and sleeves where tight tolerances and formability are needed.
PneumaticsUsed for air lines and cylinder barrels on machine tools and automation equipment.
Machine buildingMachined into bushes, spacers, rollers and guide tubes with little stock removal thanks to the close tolerances.
Bearing and cylinder componentsServes as starting stock for cylinder tubes and bearing sleeves that are later honed or ground.
Furniture and general engineeringBent and welded into frames, handles and structural parts where a clean finish is wanted.

Frequently asked questions

What does NBK mean in DIN 2391 St35 tubes?

NBK means the tube has been normalised after the final cold drawing pass, usually under a protective atmosphere. It gives the best ductility for bending and flaring and is the usual condition for hydraulic tubes.

Is DIN 2391 still a valid standard?

DIN 2391 has been withdrawn and replaced by EN 10305-1, where St35 corresponds to E235. Many drawings and spare part lists still use the DIN reference, so tubes are still ordered and certified to it.

Which delivery condition should I choose for machining?

BK or BKS are usually preferred for machined parts because the higher strength from cold drawing gives cleaner cutting. BKS also has lower residual stress, so parts move less after machining.

Can St35 tubes be welded?

Yes. The low carbon content makes St35 easy to weld by common processes without preheating in normal wall thicknesses.