Request Quote
  1. Home
  2. Products
  3. Hastelloy
  4. Hastelloy B2 Pipes & Tubes

Hastelloy B2 Pipes & Tubes

Hastelloy B2 (UNS N10665) nickel-molybdenum pipes and tubes to ASTM B622, B619 and B626 for hydrochloric acid service, supplied by Riyaarth Overseas.

Hastelloy B2 Pipes & Tubes by Riyaarth Overseas

Hastelloy B2 is a nickel-molybdenum alloy, UNS N10665 and Werkstoff 2.4617, with about 28 percent molybdenum and very low carbon, silicon and iron. It is designed for strongly reducing environments and is one of the few metallic materials that resist hydrochloric acid at all concentrations and temperatures up to the boiling point. It also handles hydrogen chloride gas and sulphuric, acetic and phosphoric acids under reducing conditions.

Pipes and tubes are made to ASTM B622 (seamless pipe and tube), ASTM B619 (welded pipe) and ASTM B626 (welded tube), with matching ASME SB numbers. Because B2 has almost no chromium, it must not be used where ferric or cupric salts or dissolved oxygen are present. Riyaarth Overseas supplies and exports Hastelloy B2 pipes and tubes with full traceability.

Because B2 is used in severe acid service, buyers often specify additional checks such as intergranular corrosion testing, PMI on every length and controlled annealing records. Welding is done by TIG with matching nickel-molybdenum filler metal and low heat input, and the weld area should be kept free of iron contamination. When enquiring, please give the specification, the size as NPS and schedule or OD and wall, the length and any project inspection requirements so we can quote accurately.

Key Features

Hydrochloric acid resistance: Hastelloy B2 resists pure hydrochloric acid at all concentrations and temperatures, a duty where stainless steels and most nickel alloys fail.

Low carbon and silicon: Carbon of 0.02 max and silicon of 0.10 max reduce grain boundary precipitation in the weld heat affected zone, so welded parts can be used as-welded in many services.

Resistance to pitting and stress corrosion cracking: The high nickel and molybdenum content gives good resistance to chloride pitting and stress corrosion cracking in reducing media.

Limitation in oxidising media: B2 contains little chromium, so oxidising impurities such as ferric ions, cupric ions or aeration cause rapid attack. Service conditions should be checked before selection.

Specifications

ParameterDetails
StandardsASTM B622 / ASME SB622, ASTM B619 / ASME SB619, ASTM B626 / ASME SB626
Grade / UNSHastelloy B2, UNS N10665, W.Nr. 2.4617
Outside diameter rangeSeamless tube from 6.35 mm (1/4 in) OD; pipe NPS 1/8 in to 6 in seamless, larger sizes welded
Wall thickness / scheduleSCH 5S, 10S, 40S, 80S, 160; tube wall in BWG or mm
LengthRandom and cut lengths
TypeSeamless, welded, welded and drawn
EndsPlain ends, bevelled ends, threaded ends on request
Form / finishRound, U-bent; solution annealed and pickled
Test certificateEN 10204 3.1 mill test certificate as standard; EN 10204 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Nickel (Ni)Balance
Molybdenum (Mo)26.0 – 30.0
Iron (Fe)2.0 max
Chromium (Cr)1.0 max
Cobalt (Co)1.0 max
Manganese (Mn)1.0 max
Carbon (C)0.02 max
Silicon (Si)0.10 max
Phosphorus (P)0.04 max
Sulphur (S)0.03 max

Mechanical Properties

PropertyValue
Tensile strength (solution annealed)110 ksi (760 MPa) min
Yield strength, 0.2% offset51 ksi (350 MPa) min
Elongation in 2 in (50 mm)40% min
Density9.2 g/cm³

Minimums are for solution annealed pipe and tube to ASTM B622.

Equivalent Grades

StandardDesignation
UNSN10665
Werkstoff Nr.2.4617
EN / DINNiMo28
Common namesHastelloy B2, Alloy B-2

Testing and Inspection

Hastelloy B2 pipe and tube are tested to ASTM B622, B619 or B626 as ordered. Typical inspection includes:

  • Hydrostatic or eddy current test: On every length as the specification requires.
  • Flattening and flaring tests: Ductility checks on samples from each lot.
  • Positive material identification (PMI): Confirms molybdenum and low chromium and iron.
  • Intergranular corrosion test: Available on request for critical acid service.
  • Dimensional and visual inspection: Full check of OD, wall, length and surface.
  • Third-party inspection: Witness inspection by your nominated agency on request.

Why Choose Riyaarth Overseas

Riyaarth Overseas sources Hastelloy B2 pipes and tubes from established nickel alloy mills and holds selected sizes for urgent requirements. We supply cut lengths with EN 10204 3.1 certificates and heat numbers on every piece.

Our team can help confirm whether B2 or an alternative such as C276 or C22 suits your process conditions, and we send prompt quotations with export packing in wooden boxes.

Applications

Hydrochloric acid productionPiping, heat exchanger tubing and coolers handling hydrochloric acid and hydrogen chloride gas.
Chemical synthesisReactors and transfer lines in alkylation, chlorination and other processes producing reducing acids.
Acetic acid plantsEquipment exposed to acetic acid and acetic anhydride under reducing conditions.
PharmaceuticalsProcess piping for acid-catalysed reactions where product purity matters.
Vacuum furnacesFurnace components operating in reducing atmospheres.
Sulphuric and phosphoric acid servicePiping for non-oxidising sulphuric and phosphoric acid streams.

Frequently asked questions

Which ASTM standard covers Hastelloy B2 seamless pipe?

Seamless Hastelloy B2 pipe and tube are supplied to ASTM B622 / ASME SB622. Welded pipe is covered by ASTM B619 and welded tube by ASTM B626.

Can Hastelloy B2 be used in oxidising acids?

No. B2 contains very little chromium, so oxidising acids, ferric or cupric salts and dissolved oxygen cause rapid corrosion. A chromium-bearing alloy such as C22 or C276 is used instead.

What is Hastelloy B2 mainly used for?

Its main use is hydrochloric acid and hydrogen chloride service, plus other reducing acids such as sulphuric, acetic and phosphoric acid.

How does Hastelloy B2 differ from B3?

B3 is a later version with controlled additions that improve thermal stability during fabrication. B2 remains in use in many existing plants and is supplied to the same ASTM product standards.