Request Quote
  1. Home
  2. Products
  3. Carbon Steel
  4. JIS STKM 13A Carbon Steel Tubes

JIS STKM 13A Carbon Steel Tubes

JIS G 3445 STKM 13A carbon steel tubes with 370 MPa minimum tensile strength for shafts, sleeves and machine parts, exported by Riyaarth Overseas.

JIS STKM 13A Carbon Steel Tubes by Riyaarth Overseas

JIS STKM 13A is one of the most widely used grades in JIS G 3445, the Japanese standard for carbon steel tubes for machine structural purposes. With carbon up to 0.25% and manganese between 0.30% and 0.90%, it offers a good balance of strength, machinability and weldability. The A suffix marks the lowest strength level of the STKM 13 group, below 13B and 13C.

Engineers choose STKM 13A for parts that are machined, welded or lightly formed and need more strength than STKM 11A or 12A can give. It is a standard choice for automotive and machinery components in Japanese and Asian designs. Riyaarth Overseas supplies and exports JIS STKM 13A tubes in seamless and welded forms, in cut lengths if needed, with mill test certificates.

Key Features

Balanced strength and ductility: A minimum tensile strength of 370 MPa and yield of 215 MPa, with 30% elongation, suits parts that are both machined and formed.

Good machinability: The medium-low carbon content gives clean turning and boring for bushes, sleeves and spacers.

Weldable: STKM 13A welds readily by common arc processes, which makes it suitable for welded frames and assemblies.

Seamless or welded supply: The tube can be ordered hot or cold finished seamless, or electric resistance welded, depending on tolerance and cost needs.

Specifications

SpecificationDetails
StandardJIS G 3445
GradeSTKM 13A
Outside diameter rangeAs per enquiry; dimensional tolerances to JIS G 3445
Wall thicknessAs per enquiry; tolerances to JIS G 3445
LengthRandom lengths, fixed lengths and cut pieces
TypeSeamless (-S-H, -S-C) or electric resistance welded (-E-G, -E-C)
EndsPlain ends, square cut, deburred
Form / finishRound; black, bright or oiled finish
Test certificateEN 10204 3.1; 3.2 with third-party inspection on request

Chemical Composition

ElementComposition (%)
Carbon (C)0.25 max
Silicon (Si)0.35 max
Manganese (Mn)0.30 – 0.90
Phosphorus (P)0.040 max
Sulphur (S)0.040 max

Mechanical Properties

PropertyValue
Tensile strength370 MPa min
Yield strength215 MPa min
Elongation (longitudinal)30% min
Density7.85 g/cm³

Elongation applies to the longitudinal test piece in JIS G 3445; transverse values are lower.

Equivalent Grades

STKM 13A has no exact equivalent in other standards. It is often compared with EN 10305 grades such as E235 and E255, or with ASTM A519 grade 1020 for machining work, but chemistry and strength limits are not identical, so any substitution should be confirmed against the drawing.

Testing and Inspection

STKM 13A tubes are inspected to JIS G 3445 and the purchase order:

  • Chemical analysis: heat analysis against the grade limits.
  • Tensile test: tensile strength, yield strength and elongation.
  • Flattening test: for ductility and weld soundness on welded tubes.
  • Non-destructive testing: eddy current or ultrasonic testing when ordered.
  • Dimensional inspection: outside diameter, wall thickness, straightness and length.
  • Third-party inspection: available on request with EN 10204 3.2 certificates.

Why Choose Riyaarth Overseas

Riyaarth Overseas works with established tube mills for STKM 13A and can supply it seamless or welded, in fixed or cut lengths. Every lot is backed by an EN 10204 3.1 mill test certificate and packed for export in protected bundles. Send your size list and quantity for a fast quote.

Applications

AutomotiveMachined into axle sleeves, steering and suspension parts and spacers.
Motorcycle componentsUsed for frames, swing arm parts and fork components that are welded and machined.
Machine toolsTurned into bushes, collars and guide tubes for spindles and slides.
Agricultural machineryUsed for shafts, pivots and welded frames on tractors and implements.
Material handlingFormed into rollers, conveyor shafts and trolley frames.
General engineeringStocked by fabricators as a standard tube for welded structures and machined parts.

Frequently asked questions

What is the difference between STKM 13A, 13B and 13C?

All three share the same chemical limits. They differ in strength: 13A is 370 MPa tensile minimum, 13B is 440 MPa and 13C is 510 MPa, with elongation falling as strength rises. The higher grades are usually reached by cold working.

Can STKM 13A be heat treated?

It can be normalised or stress relieved. Because carbon is limited to 0.25%, it does not harden much by quenching and is not a through-hardening grade.

Is STKM 13A good for machining?

Yes. It is commonly used for turned bushes, sleeves and spacers, and its moderate carbon content gives good chip formation and surface finish.

Can STKM 13A replace an EN 10305 tube?

It may, but the standards differ in chemistry, strength and tolerances. Check the drawing requirements and get approval before substituting.